Bedienungsanleitung Gazco Vision Large MK2 Series Balanced Flue Instructions (Seite 25 von 36) (Englisch)

813416

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

1. Servicing Requirements

IMPORTANT – The glass panel on this appliance should be

checked for any signs of damage on the front face of the

glass panel (scratches, scores, cracks or other surface

defects). If damage is observed, the glass panel must be

replaced and the appliance must not be used until a

replacement is installed. Under no circumstances should the

appliance be used if any damage is observed. Please isolate

the appliance until a replacement glass panel has been

obtained and installed. Replacement glass panels can be

purchased from Gazco via the retailer from which the

appliance was purchased or any other Gazco distributor.

This appliance must be serviced at least once a year by a

competent person.

All tests must be carried out in accordance with the current Gas

Safe recommendations.

1.1 Before Testing:

— Conduct a gas soundness test for the property ensuring

there are no leaks before servicing.

— Check the operation of the appliance before testing.

1.2 Special checks:

— Clean the burner using a vacuum cleaner with a soft

brush attachment. Ensure all debris is removed from the

burner ports.

— Clean away lint or fluff from the pilot.

— Clean away lint or fluff from under the burner.

— Check the spark gap on the pilot is correct.

1.3 Correct any faults found during the initial test.

1.4 Re-commission the appliance in accordance with

Commissioning Procedures of these instructions.

1.5 Advise the customer of any remedial work undertaken.

REPLACE BATTERIES BEFORE ATTEMPTING TO RECTIFY

ANY FAULTS.

Symptom Cause Remedy

3 Short beeps from

control

Batteries low in

appliance

Replace appliance

batteries

No ignition, 5 second

continuous tone (there

may be several short

beeps before)

Loose/damaged wire Check interrupter

block and wires

No ignition, no tone,

motor turns slightly

when operated

Receiver board

damaged

Replace receiver

No pilot flame and

control continues to

spark

Thermocouple circuit

wired incorrectly

Correct wiring

Pilot lights, control

continues to spark,

valve shuts down after

10 - 30 seconds

1. No spark at pilot

burner

2. Loose/damaged

wire

1. Rectify spark at

pilot burner

2. Check

interrupter and

wires

ELECTRONIC CONTROL VALVE FAULT ANALYSIS

IGNITION FUNCTIONAL CHECK 1

PILOT WILL NOT LIGHT

Ensure there is no debris around the pilot assembly,

(e.g. soot, etc.) which could short the spark, clean the

area.

Operate the valve

control system in the

manual mode via the

touch pad or remote. Is

there a spark?

Consult User

Instructions and retry.

Check alignment of pilot

burner head. Change the

ignition lead.

See Replacing Parts,

Section 9.

Check isolation tap and

gas meter, retry.

Correct and

retry.

Purge the gas pipes and

retry.

GO TO THE NEXT

CHART IGNITION

FUNCTIONAL CHECK 2

SYSTEM OK

There is a blockage in the system, check the inlet test point,

the mag seating and valve. Check thermocouple leads for correct

orientation, condition and connection

Is the gas turned on to the

appliance?

Is the gas pressure correct?

Has the system got

any air in it?

Does the pilot light?

Is the control being

operated correctly?

Will the pilot light

with a match?

No Yes

Yes

Servicing/Fault Finding Charts

Servicing Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Vision Large MK2 Series Balanced Flue Instructions Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info