Bedienungsanleitung Geba Tronic Cody T4 (Seite 8 von 11) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

544622

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Instructions for Assembly and Use

TCS - Cody - T4

Electronic encoder-type lock for electric door-openers

The TCS-Cody-T4 is a modern and safe keyless door-opening system. The TCS-

Cody-T4 can safely be used after programming the pass code. For opening the

door only a four- or five-digit numeral code (pass code) has to be entered

After correct input of the pass code and pushing the key button the electric door-

opener is activated.

Assembly Instructions

Assembly of the CODY keypad:

1. By slightly pushing the two latches at the right and left side of the keypad

from behind to the edge, remove the small frame from the keypad.

2. Now you see two fixingholes (diam. = 4 mm) at the front of the keypad.

By means of these you can fix the keypad onto the wall.

3. Connect the keypad to the logic unit by means of the twin-cable (up to 5 m long).

There is no particular polarity for the twin wires.

4. Now re-fix the small frame.

5. It is possible to connect in parallel up to four keypads if a thin connection cable, max.

total line cross-section 1.5 mm

, is used.

Keypads connected in this way must not be operated simultaneously.

Assembly of the logic unit (inside area):

1. Put the screw-driver into the gap of the enclosure front, push the screw-driver up and

open the enclosure.

2. Remove the control PCB (which is force fitted to the inside of the enclosure).

3. Locate the screwed glands supplied (sealing nipple left side) in the

enclosure and replace the PCB. (Please ensure PCB is firmly in position)

4. Bore the fastening holes and fix the enclosure bracket at the wall.

5. The wires for the keypad ensure through the left cable entry (sealing nipple), the wires

for the relay contact through the middle cable entry and the wires for the supply voltage

ensure through the right cable entry. Ensure tight seating of sealing nipple and cable

gland, otherwise the water-protection ot the appliance cannot be assured.

6. According to connection diagram connect the wires to the corresponding terminals.

geba GmbH is released of its obligations regarding guarantee and product liability if - without prior

permission - the unit has been modified, or if the installation is improper or not in accordance with

our instruction manual.

The installer has to take care that the EMC-regulations are respected.

The most important characteristics of the TCS-Cody -T4 are:

⇒⇒ Simple operation, programming and assembly.

⇒⇒ Water-protected enclosure.

⇒⇒ A maximum of safety:

⇒⇒ The electronic decoder is separately installed in the

protected area

⇒⇒ 4 different pass codes can be stored

⇒⇒ Nearly unlimited data security, even with power failure

⇒⇒ Direct connection of electric door-opener.

industrial controls

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Geba Tronic Cody T4 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info