544888
3
Zoom out
Zoom in
Vorherige Seite
1/3
Nächste Seite
Programming of ROLLOTIMER Comfort - with S/D sensor
1. Enter programming mode
Press ▲ (UP) and ▼ (DOWN) simultaneously for
approx. 3 seconds.
2. Sun function
setting
(only with S/D
Sensor)
Setting of value
0 ... E
Use ▲ (UP) to set the value or E for calibration
of the current lightning conditions.
Press ▼ (DOWN).
3. Dusk function
setting
(only with S/D
Sensor)
Setting of value
0 ... E
Use ▲ (UP) to set the value or E for calibration
of the current lightning conditions.
Press ▼ (DOWN).
Continue with point 2 programming of the Timer Comfor t- without S/D-Sensor
Value S/D Sensor
Value Sun sensor Dusk sensor
0 Deactivated / off Deactivated / off
1 Low brightness Low dusk
2 Medium brightness Medium dusk
3 High brightness High dusk
E Calibration of the sensor
Calibration of the sensor
Settings : Sun / Dusk sensor, (Art. No.: 607.S000.01)
This is only available if a S/D sensor is connected and if the automatic mode is activated. For the
installation of the sensor please see the next page of the manual. The Timer will require approx. 10
seconds for the correct identification, after switching on.
Sun function
If a S/D sensor is connected, activated and the automatic mode is activated, a sun symbol will appear
in the display. Exceeding the set brightness value is indicated by a blinking of this symbol. If the set
brightness value is exceed by more than 10 minutes, the blind will be lowered until the sensor is in the
shadow again. The Brightness is checked every 30 minutes. If the set value is underrun for 10
minutes the blind goes up again.
Dusk function
If a S/D sensor is connected, activated and the automatic mode is activated, a moon symbol will
appear in the display. Exceeding the set dusk value is indicated by a blinking of the symbol. The
function of the dusk value is switched on by the automatic set ▼ (DOWN) operation mode. If the value
is exceeded by 10 mor e than minutes, the blinds will close completely. Please note that any light
source near the sensor can interfere with its function.
Calibration of the S/D sensor
If you experience any problems with the preset brightness values, you can calibrate the S/D sensor
individually to the desired brightness. When you have the desired brightness, select the value „E“.
Then press ▼ (DOWN) to the current brightness as value 2 – medium brightness/dusk. Define and
save.
Attachment of the Sun / Dusk sensors
Remove the upper part together with the two frames of the ROLLOTIMER.
Now have a look on the image below. Connect the sun / dusk sensor with the plug.
Please make sure, that the C-frame (extremely remote frame) has a cable through hole on the
requested side.
Plug to connect the
sun / dusk sensor
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Geba Tronic ROLLOTIMER Comfort wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Geba Tronic ROLLOTIMER Comfort

Geba Tronic ROLLOTIMER Comfort Bedienungsanleitung - Deutsch - 4 seiten

Geba Tronic ROLLOTIMER Comfort Bedienungsanleitung - Holländisch - 3 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info