Bedienungsanleitung Wellis Aquasoul Pro (Seite 57 von 108) (Englisch)

784851

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

UVC WATER TREATMENT

WARNING: THE GERMICIDAL ULTRAVIOLET RAYS

ARE HARMFUL TO THE EYES, SKIN.

INTEGRATION:

1. Install the sterilization equipment at an easy to reach well

lit place for effortless observation and maintenance.

2. Lock the clamp on the frame.

3. Insert the chamber with the help of the clamps.

4. Connect to the water supply.

5. Insert the quartz sleeve, sealing ring, lamp.

IMPORTANT: DO NOT TOUCH THE QUARTZ SLEEVE

OR THE SIDES OF THE LAMP, ONLY HOLD IT BY THE

TWO ENDS.

The ultraviolet lamp and the quartz can easily be damaged.

Take care when removing or changing the lamp or the quartz

sleeve.

a. Take off the nut. (2).

b. Carefully slide the quartz sleeve (6) from one end of the

chamber to the other.

c. Slide the sealing ring (5) onto the free end points of the

quartz sleeve.

d. Squeeze the aluminum nut on by hand (2).

e. Slide the lamp (4) into the quartz sleeve.

f. Connect the lamp to the casing.

g. Screw the nut to the chamber, then screw on the water

resistant lid (1) to the nut (2).

h. Open the tap and check if the device is leaking. Repair as

necessary.

I. Plug the device into the electric supply. Use a socket

equipped with a fault circuit interrupter (GFCI).

Malfunction of the UVC water sanitizer is indicated by the LED

logo flashing in red. In this case, replacement of the fluores-

cent tube is necessary.

CHANGING THE LAMP AND SERVICING THE UV

SYSTEM

Important: Do not touch the quartz sleeve or the sides of the

lamp, only hold it by the ends.

1. Unplug the power plug.

2. Shut down and drain the water from the device to lessen

pressure.

3. Take off the PVC lid (1) and unscrew the aluminum nut (2).

4. Carefully pull out the lamp (4) to approximately 5cm from

the chamber (7).

5. Holding the lamp by the end carefully remove the lamp

casing (3) on the free end.

6. Carefully take the lamp out of the chamber.

7. Carefully take off the sealing ring (5) from the end of the

quartz sleeve.

8. Carefully take off the quartz sleeve.

9. To reinstall follow instructions 1 to 8 in reversed order

MAINTENANCE SUGGESTION:

In order for the sterilizer to work properly and with maximal

efficiency the user should perform the following mainte-

nance tasks.

1. Cleaning, changing the quartz sleeve:

a) The quartz sleeve is to be cleaned with a glass cleaner

solution every 6-12 months.

b) The quartz sleeve is to be changed every 24 months.

2. Changing the UV lamp is recommended after 8-9000 op-

erating hours (about 12 months of continuous operation).

3. To acquire interchangeable parts contact our headquar-

ters or the local representatives of our company.

1- Water resistant lid

2- Aluminum nut

3- Lamp casing, wire outlet

4- Germicidal ultraviolet lamp

5- Rubber sealing ring

6- Quartz sleeve

7- Chamber

8- Pawl

9- Transformer

OPTIONAL ACCESSORIES  UVC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis Aquasoul Pro Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wellis Aquasoul Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info