Bedienungsanleitung Wellis Aquasoul Pro (Seite 61 von 108) (Englisch)

784851

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

You can choose between four different water regulation

modes available. Your in.grid is automatically detected by the

spa control system at power up. It will be ready to use with

your preferred heat mode one minute following power up.

The relay contacts of the in.grid will be closed if the external

heating system is activated. Otherwise, the relay contacts

are open.

Your desired heat mode must be set by adding a jumper on

one of the five (5) different positions.

*Note: Your heat mode selection can be changed with the

in.touch 2 app on your mobile device. On your app, any new

selection will override the jumper setting of the in .grid. The

in.touch 2 app will automatically detect the in.grid presence and

will adapt its menu configuration as required.

Heat mode

selection

Diagnostic

LED

Heat

LED

Five available heat modes are offered with in.grid:

1- DIS (DISABLED)

Use this mode if the spa configuration does not have any

external heating system and only the single switch func-

tionalities are used. This will avoid in.touch 2 application on

a mobile device to display the Heat Mode Selection menu*.

The spa controller will regulate the water temperature using

the standard resistive heater. The single button switches

will control the different spa accessories according to the AC

jumper selections.

IMPORTANT: This mode can only be set with the heat mode

jumpers.

2- INT (INTERNAL)

This mode provides an easy way to revert back to standard

water regulation using the internal heater in case of problem

with the external heating system.

* This mode can be set with your in.touch 2 app on a mobile

device without the need to open the spa skirt to change the

jumper setting on the in.grid. Thanks to your in.touch 2, it will be

easier to set your preferred heating mode back once the external

heating system is available.

3-EXT (EXTERNAL)

Use this mode for a maximum energy saving purpose. The

spa control system will only use your external heating system

to regulate the water temperature. In normal operation, the

internal heater will never be activated.

* This mode can be set with your in.touch 2 app on a mobile de-

vice without the need to open the spa skirt to change the jumper

setting on the in.grid.

Freeze Protection

Freeze protection has been added because EXT (EXTERNAL)

mode does not allow the activation of the internal heater.

In cold weather, if it becomes impossible to keep the water

over freezing point, the help of the internal heater will then

be needed. This is the only time the freeze protection will

come in.

At any time, if the water temperature drops to 40°F (4.5°C),

the resistive heater will give a boost to avoid freezing. The

freeze protection will stay active until water temperature

reaches the minimum allowed set point (usually 59°F / 15°C).

Normal EXT mode will resume functioning thereafter.

4- BOTH (BOTH SYSTEMS ALL AT ONCE)

Use this mode for swim spas or large spas, which have bigger

needs of energy to keep the water temperature at the desired

set point.

The spa control system will always use the external heating

system AND the internal heater simultaneously to regulate

the water temperature; they are both activated or deactivat-

ed at the same time.

* This mode can be set with your in.touch 2 app on a mobile de-

vice without the need to open the spa skirt to change the jumper

setting on the in.grid.

5- SMART (ENERGY SAVINGS)

Use this mode for a better energy saving purpose, combined

with a maximum water temperature regulation efficiency.

The spa control system will always use the external heating

system to regulate the water temperature. If the temperature

falls too far below your set point (-2.5°F), the internal heater

will be activated to help your external heating system reach

the set point.

Once the temperature is within 1.5°F from set point, the in-

ternal heater is deactivated and the external heating system

takes all control of the water regulation again.

* This mode can be set with your in.touch 2 app on a mobile de-

vice without the need to open the spa skirt to change the jumper

setting on the in.grid.

Troubleshooting

DIAGNOSTIC LED

The diagnostic LED will help you with the status of the con-

nection between the spa control system and the in.grid.

Blinking light: Spa control system not detected, not

compatible or in Disable mode if one of your

single switches doesn’t operate properly.

Solid light: Spa control system detected

No light: Power Off

HEAT LED

Solid light: Relay contacts close and external heating

system on.

No light: Relay contacts open and external heating system

off.

OPTIONAL ACCESSORIES  IN.GRID

Heat Mode Operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis Aquasoul Pro Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wellis Aquasoul Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info