Bedienungsanleitung Wellis In.Grid (Seite 11 von 108) (Englisch)

784855

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

SETTING FILTER

OR PURGE CYCLE

FREQUENCY

The display will show FFxx,

“xx” representing the number

of cycles per day. Use the Up

or Down key to adjust the

frequency. Use the Light key to

jump to the next parameter,

economy mode (EP).

The “Filter cycle” indicator

lights up when filter is on and

flashes when suspended.

SETTING FILTER

CYCLE DURATION

(not available on purge

systems)

The display will show Fdxx,

“xx” representing the dura-tion

in hours of the filter cycle. Use

the Up or Down key to adjust

the duration. Use the Light key

to jump to the next parameter,

filter or purge frequency (FF).

0 = no filtration

24 = continuous filtration

It is not recommended to set

this to "0".

PROGRAMMING STEPS

PROGRAM

The program menu is accessible

by holding down the Light key

for 5 seconds. In the program

menu the following parameters

can be set: clock, the filter or

purge cycles, economy mode

and temperature units. While

you are in the program menu,

use the Up or Down key to

adjust the parameters and use

the Light key to jump to the

next parameter.

The changes will be saved after

the confirmation of the last

parameter only. If there is no

action taken for 10 seconds, the

system will exit the program

menu without saving any

changes.

SETTING THE

CLOCK

Enter the program menu by

holding down the Light key

for 5 seconds. The display will

show the current clock setting

with the hour flashing.

Depending on factory settings

your system may be set to 24-

hour time or 12-hour time.

Setting the hour: Use the Up

or Down keys to adjust the

hours. Press the Light key to

jump to the next parameter,

the minutes.

Setting the minutes: Use the

Up or Down keys to adjust the

minutes. Press the Light key to

jump to the next parameter,

the filter or purge start time

(FS).

SETTING FILTER

OR PURGE CYCLE

START TIME

The display will show FSxx, “xx”

representing the starting hour

of the cycle. Use the Up or Down

key to adjust the hours. Use the

Light key to jump to the next

parameter, filter duration (Fd).

PROGRAMMING

THE FILTER/ PURGE

CYCLES

Depending on system config-

uration your spa will perform

either a filter or a purge cycle.

The filter cycle menu consists

of the following parameters:

the start time (FS), the duration

(Fd) and the frequency (FF).

The purge cycle menu consists

of the following parameters:

the start time (FS) and the

frequency (FF).

A filter cycle consists of start-

ing all the pumps and blower

in high speed for 1 minute

(purge step) then, the pump

associated with the filter

will run in low speed for the

remaining duration of the

filter cycle (clean step).

A purge cycle is used when

the spa is equipped with a 24

hour circulation pump which

provides a continuous clean

step. It consists of starting

all the pumps and blower in

high speed for 1 minute.

USER INTERFACE  EASY 4

SETTING ECONOMY

MODE

This mode allows you to lower

the temperature set point of

the spa by 20 °F (11 °C) during a

certain period of the day.

The display will show EPx, “x”

representing the state of the

programmed economy (0 =

disabled, 1 = enabled). Use

the arrow keys to enable or

disable economy mode. Use

the Light key to jump to the

next parameter, economy start

time (ES).

Note that the parameters for the economy mode settings are

associated to specific low level configuration of the system that are

not present in all software revisions.

SETTING ECONOMY

START TIME

The display will show ESxx,

“xx” representing the hour at

which the economy mode will

become active. Use the Up or

Down key to adjust the hour.

Use the Light key to jump to

the next parameter, economy

duration (Ed).

When the Economy mode is ON,

the display will toggle between

the “Eco” message, the time,

and the water temperature.

SETTING ECONOMY

DURATION

The display will show Edxx, “xx”

representing the duration in

hour of the economy mode. Use

the Up or Down key to adjust

the hour. Use the Light key to

jump to the next parameter,

temperature unit.

24 = continuous economy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis In.Grid Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wellis In.Grid

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info