Bedienungsanleitung Wellis In.Touch2 (Seite 8 von 108) (Englisch)

784856

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

SITE PREPARATION

When choosing a site for the spa take into account that its

maintenance and repair works must be carried out behind

the sidewalls, so accessibility and space to walk around the

spa must be ensured.

1. INDOOR/BASEMENT INSTALLATION

If you place your spa indoors, be aware of some special

requirements:

Water may accumulate around the spa, so the flooring mate-

rial must have a proper runoff to avoid accumulation of water.

When building a new room for the spa, constructing a floor

drain is required, or damages may occur due to overflow,

overfilling, or technical failure. Our company does not take

responsibility for any damage in absence of floor drainage.

Humidity will naturally increase in the room where the spa is

located and the evaporated water condenses. For this reason

ensure that the area has proper ventilation. We recommend

installing a dehumidifier in the room.

2. OUTROOR AND PATIO INSTALLATION

A solid horizontal foundation is necessary for installation of

the spa. We advise using a reinforced concrete foundation at

least 10-15cm thick.

Ensure that your deck or foundation will support your spa.

You must know the maximal load capacity of the foundation.

Consult a qualified building contractor or structural engineer.

To find out the weight of your spa, its contents and occupants

please refer to the spa specification chart. This weight must

not exceed the structure’s rated capacity per square meter,

otherwise serious structural damages could result. If you

install the spa outdoors, we recommend a reinforced hori-

zontal concrete pad at least 10-15cm thick.

Install floor drains around your spa to lead water away even

in heavy rain.

When constructing the water drain it is advised to form a 10-

15cm deep sloping ditch around the spa which directs water

to the drain. Water from the drain must be directed to the

canal or a drainage with enough capacity.

Warning: Do not expose the spa to direct sunlight (not even

empty) without proper coverage. The insulated spa cover

preserves the water temperature and provides protection from

sunlight and rain. When exposed to sunshine for a longer period

it may damage the surface of the spa and the spa equipment.

Acrylic rapidly absorbs heat from sun rays, thus reaches a

very high surface temperature which may damage the spa.

In case of sealed design, if the spa was placed between glass

structures, prevent the sun rays from reaching the spa direct-

ly through the glass as the temperature may get too high.

3. IN-GROUND / SUNKEN SPA

In case of sinking the spa into the ground you must make

sufficient space for walking around the spa. For completion

of maintenance works a minimum of 60cm wide inspection

pit must be built around the spa.

The inspection pit’s bottom must be under the bearing pont

of the spa so that water can flow into the pit in case of water

leakage. A floor drain or sump pump should be used at the

bottom of the pit to ensure continual water drainage.

In case of sinking the spa only the portion below the spa’s

acrylic edge can be sunk. The air of the inspection pit steams

up. To prevent unpleasant odors proper ventilation must be

provided (e.g. installing ventilators). The costs of pulling the

spa out of the ground are borne by the user. If the aforemen-

tioned conditions are not present, setting up the spa may fail.

First filling of the spa

Proper filling of the spa is an important task both technically

and chemically. We advise installation and periodic mainte-

nance by the servicing professionals, which includes inspec-

tion and refilling of spa water. Spas do not contain water

softener and hard water damages the equipment. Improper

filling of the spa may bring air into the system, which damag-

es the heating wire and engines. Pure stream WE00067 (water

softener) and Pure fill WE00068 (carbon filter) are ensured for

your spa. Please fill your spa exclusively through this filters.

Repairs after such failures are not covered by warranty.

Filling process

Remove the spa cover. First remove the cover staves, then

remove the side covers by unscrewing the bottom screws.

During transportation the flare fittings of engines may

dislocate. Check these connections before installation. If

necessary, tighten the flare fittings.

In spas equipped with air engine the flare fitting must be

connected before running the spa for the first time.

Before filling the spa check that the ratchets are not in a

closed state (lever is pulled out and fixed with the safety

lock).

Next fill the spa with water to the sign indicated on its

sidewall.

Filling must be done through the filter housing. Improper

filling can damage the engines and heating element.

Insert the filter or filter cartridges when proper water level

is reached. Be cautious, because when replacing the filter

cartridge air bubbles may remain in the cartridge. To avoid

this the filter cartridges must be tilted in the water to remove

air from them, and only then fitted to their place.

INITIAL INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis In.Touch2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wellis In.Touch2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info