Bedienungsanleitung Wellis Pulsar (Seite 106 von 108) (Englisch)

784854

106

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

QUESTIONS CONCERNING CLEANING, WATER

TREATMENT, AND MAINTENANCE

What should I do if the filter of the spa is polluted?

Clean the filter every week or two weeks with a jet of water.

Periodically, depending on usage, soak the filter in water

mixed with an antialgae agent for 1-2 hours, then rinse it.

Should I shower before using the spa?

Yes, thoroughly.

Should the side cover of the spa be treated?

The side cover is made from weather resistant plastic. It does

not require treatment or maintenance (except if it is a cedar

cover).

How often should the water be changed if my spa has the

in.clear water maintenance system? Does it maintain

water quality?

With the cutting-edge automated brominating in.clear sys-

tem water only has to be changed approximately once every

6 months. This can be even longer if the spa is not used daily.

Adding water and Trublu (sodium bromide) may be necessary

if the water level decreases because of splashing or evapora-

tion. Optional UV-C antibacterial agents, disinfectant, and a

sterilization system are available for our spas. These guaran-

tee fresh and pure water using 30-50% fewer chemicals.

What kind of water treatment do you recommend in case

of communal use?

In case of communal use we recommend the optional

sand filtration device that comes in place of the standard

antibacterial filter. In case of heavy usage we recommend the

automated monitoring-, regulating-, and chemical dispenser

device.

I cannot stop the heavy foaming. Before using the spa

we shower without using soap and I use the necessary

chemicals. Did I use too little?

As descriped in the user guide of the products, apply 1-2 cups

of antifoaming agent to the spa water. Wait for the chemical

to thoroughly mix with the water. Repeat if necessary. If

the problem is still present, check and readjust the pH value.

If foaming still occurs, disinfect the spa with an antialgae

chemical containing free active chlorine, then drain, clean,

rinse, and refill the spa.

PREPARATION OF THE INSTALLATION SITE

What are the most important concerns when selecting

theinstallation site?

The installation site should be prepared in accordance with

the installation guide by a professional. The devices can only

be installed and set up at appropriate installation sites. Make

sure there is an appropriate cable length, electric supply,

a 30mA protective relay, and with certain products a floor

drain.

Is a floor drain necessary for an indoor spa?

Building a floor drain is mandatory!

TECHNICAL DATE OF THE PRODUCT, USAGE

What type of water circulation engine is used for mas-

sage spas?

Our massage spas are equipped with Laing low power (110W)

energy saving, silent circulating motor pumps.

What is the maximal temperature that does not damage

the spa?

The water temperature can be adjusted to between 26 and

40 degrees Celsius.

What is the recommended optimal water temperature?

32-38 degrees Celsius. If young children are using the spa,

lower temperature is recommended. Always check the water

temperature before the child steps into the spa and make

sure that the temperature is suitable for the child.

Can the system freeze? Is there a sensor that starts emer-

gency heating in case of freezing?

In the winter the unused spa should be winterized. After

draining the spa we will defrost the system as necessary,

meaning that we will remove the water retained by the

engine and the pipes. For details and pricing please call our

customer service. If the spa remains in use during the winter,

the engines start if there is a danger of freezing and heat the

water to 8°C

Can the system be programmed to start heating at

certain time?

There is no way of setting a time and date for automatic heat-

ing. Because of concerns of energy efficiency heating the

water to greater temperatures is not recommended in case of

multiple weekly usage.

The jet of the spa shuts down automatically after 15

minutes of operation. Can I restart it immediately, or

do I have to wait? Can I restart it as many time as I want

without a break? How does this affect the jets?

The hydromassage system shuts down every 15 minutes for

security reasons - to avoid possible muscle soreness. It can

be restarted for any amount of times and without a break.

Is this the same for the bubble massage function?

Yes, it is the same for the bubble massage function.

FREQUENTLY ASKED QUESTIONS

104

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis Pulsar Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wellis Pulsar

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info