Bedienungsanleitung Geemarc Amplicall 6 (Seite 1 von 2) (Englisch)

762343

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

123

USER GUIDE

Note: For lamps with a weight significantly higher than that of

the lamps for which they are a replacement, attention should

be drawn to the fact that the increased weight may reduce the

mechanical stability of certain luminaires and lamp holders

and may impair contact making and lamp retention.

!!! Please refer to our website: www.geemarc.com for an

up to date user guide, as there may be important

updates and changes you need to be made aware of !!!

1. Introduction

Congratulations on purchasing your Geemarc AMPLICALL6.

The Bulb unit (The AMPLICALL6) receives a transmitted signal

from any number of AMPLICALL transmitters. For example, the

AMPLICALL1, 2,3, 30 & 40 and extra AC6 LR.

2. Unpacking the AMPLICALL6

When unpacking the AMPLICALL6, you will find the following

in the box:

• 1 AMPLICALL6 Unit

• 1 master remote with battery

• 1 user guide.

3. General Description

Rated current: 0.022A

ta: 35 ℃

4. Mounting

• Turn off the power of your house light fitting

• Remove the Bulb

• Place the AMPLICALL6 Bulb

• Turn on the power

• Now you can use the remote to turn on your light.

5. Pairing

Once power is connected (every time if AC is connected),

Green LED will light for 10 seconds. This means the LED

bulb is in pairing mode.

6. Pair with AC1, 2, 30, 40 (option)

If the LED bulb is under pairing mode, then press the AC1

(AC2, AC30-40 and smoke alarm etc.) to pair with the LED

device.

If the 1st AC1 is paired with the bulb, the bulb White LED will

flash once: W – .

If the 2nd AC1 is paired with the bulb, the bulb White LED will

flash twice: W – W.

If the 3rd AC1 is paired with the bulb, the bulb White LED will

flash three times: W – W – W.

If the 4th AC1 is paired with the bulb, the bulb White LED will

flash four times: W – W – W – W.

Remarks:

• AC6 is able to pair with 4 x AC6 LR. 4x extra device e.g.

AC1, 2, 3, 4 and 10x smoke alarm.

• If the LED bulb is under pairing mode, then press the

Smoke alarm button, if the smoke alarm is paired with the

bulb,the bulb White LED will flash once.

7. Pair with AC6 LR Remote Dim/Highlight/OFF switch

AC6 LR (Master Dim / Highlight / OFF) control is already

pre-paired in the factory.

User does not need to do the pairing procedure.

In case the user wants to have extra AC6 LR to control the

light bulb Dim / Highlight / OFF, then one can pair extra AC6

LR with the LED bulb. Just follow the above pairing procedure.

Remarks:

• Geemarc LED bulb is able to pair with a maximum of 4 x

Bulb

Remote

C6 LR

E27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Geemarc Amplicall 6 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Geemarc Amplicall 6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info