519999
19
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
If the handset is in power off mode, when you
p l ac e th e h a n d s e t o n t h e b a se , it
automatically turns on. To turn the handset on
or off in Standby mode, follow these steps:
1. To turn on the handset when it's off, press
and hold the key until you switch the
display on. On power up, the handset will
enter subscription mode and search for a
registered base. A message as shown
below will be displayed to the user, and the
signal icon will flash.
46
15
Note:
If the handset is successful in finding a
base, the handset will enter the Standby
mode, the display will show handset
number and the handset name (if you
have one saved as described on page 24),
signal icon, battery icon and current time.
If the handset is not successful in finding a
base, the handset will behave according to
the Out Of Range condition.
Turning Handset On/Off
2. To turn the handset off, keep the key
pressed until the display turns off.
Note:
Nothing will appear on the LCD when battery
power is very low. YOU SHOULD FULLY
CHARGE THE HANDSET BEFORE USING.
Searching...
TAM Functions (AMPLIDECT285™ only)
Announcement (AMPLIDECT285™ only)
It is necessary to record the announcement which
requests the caller to leave a message when
nobody is at home. The answer and record
message (Announce1) and the answer only
message (Announce2) can be up to 3 minutes
respectively.
Record Announce1
Auto-answer Announce1 is a conventional
message requesting you to leave a message. If
you have not recorded a personal Announce1, the
unit will play the default one "Hello, your call
cannot be taken at the moment, to record
your message, please speak after the tone".
2. Press the Select soft key to choose Announce.
3. Press Select key again to choose Announce1.
4. Press the key repeatedly to choose
Record, press the Select soft key.
5. You can record your announcement after a
tone. Recording will stop automatically after 3
minutes. You can also confirm and end the
recording by pressing the OK key. During
recording the LCD shows "Recording...".
If you want to change Announce1, do the
following steps to update it:
1. Press the TAM soft key in Standby mode.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Geemarc AmpliDECT 280 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Geemarc AmpliDECT 280

Geemarc AmpliDECT 280 Bedienungsanleitung - Deutsch - 67 seiten

Geemarc AmpliDECT 280 Bedienungsanleitung - Holländisch - 38 seiten

Geemarc AmpliDECT 280 Bedienungsanleitung - Französisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info