Bedienungsanleitung Geha S5 - Shredder (Seite 8 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

749283

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

1. Operate the device only if it stands on a level ﬂoor.

2. Check the cutting unit to ensure that it is properly placed on the bin.

3. Insert the plug of the power cord into a standard power socket.

5. Never insert metal objects, jewellery, hair, ﬁngers, cloths, etc. into the paper feeder of the

shredder.

6. Before shredding a document, remove paper clips and staples.

7. Regularly empty the paper bin to prevent paper jams.

8. Do not switch on the device if its plug or power cord is damaged or if the shredder does not

work properly or is otherwise damaged.

9. In the event of an emergency, disconnect the shredder from the power supply by pulling the

plug.

10. Where possible, install the device near a power socket and ensure that the socket remains

freely accessible.

11. Do not clean the shredder with cloth or detergents containing aerosols or solvents.

12. Do not spray the device with liquids. Do not treat with oil spray.

INSTALLING SHREDDER

STARTING SHREDDER

PREVENTING PAPER JAMS AND OVERLOADING

The S5 is operated by means of a sliding switch located at the top of the shredder. This switch can

be set to three positions: AUTO, OFF, REV. Set the sliding switch to AUTO to activate automatic

paper intake as soon as a document is placed in the feeder slot, triggering the release switch in

the feeder opening. If the sliding switch is set to OFF, the shredder does not automatically start

up when a document is placed in the feeder opening. We recommend setting the switch to this

position when the shredder is not in use. Set the sliding switch to REV, if you wish to operate the

shredder continuously in reverse mode. This is required to clear a paper jam in the feeder.

The S5 can shred up to 5 sheets (DIN A4, 70g/m²) at a time and can handle documents of up to

220mm in width. If you wish to shred smaller pieces of paper such as envelopes and sales re-

ceipts, insert them at the centre of the feeder slot to ensure that the switching sensor is trigge-

red.

The S5 is equipped with a motor overload circuit breaker. A normal operating cycle for shredding

at maximum load takes 2 minutes, which must be followed by a break in operation. The power

supply to the shredder motor is automatically interrupted in the following cases:

1. Continuous operation of the document shredder at maximum capacity overa prolonged period

of time, i.e. for more than 2 minutes without interruption.

2. Simultaneous insertion of more than 5 sheets of paper (DIN A4, 70g/m²) or feeding of paper in

a direction other than longitudinal.

Under the above conditions, the automatic overload circuit breaker of the motor might be trigge-

red, interrupting the power supply to the device. If this occurs, proceed as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Geha S5 - Shredder Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info