479875

Gemini 7463 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/5
Nächste Seite
OUTLET FROM THE PROGRAMMING PROCEDURE OF THE ACCESSORIAL FUNCTIONS.
It is possible to leave any moment the programming procedure turning the ignition key to OFF. In this
case it is obtained the memorisation of the condition for the changed functions and the confirmation of
the previous condition for the unchanged functions.
Otherwise, if the procedure is carried out for all the functions described in the table, at the end of the
programming of the last function (double pulse while opening), the system will automatically leave the
procedure.
In both above-mentioned situations the abandonment of the programming procedure is signalled by
two audible signalling with low tone (BOP) and by one signalling with high tone (BIP) followed by the
Led switching off.
WORKING DESCRIPTION
ALARM ARMING
Press on the transmitter’s rough button (button 1). The arming is signalled by one flashing of the direction
indicator lights and one audible high tone (BIP). The emission of the audible signalling is subordinate to the
programming condition of the accessorial function “AUDIBLE SIGNALLING”.
Besides the activation of the optic/acoustic s ignalling at the same time activates also the locks closure control
(with the time set in the programming phase of the accessorial functions) and the activation of the following
functions:
1) INTERNAL BATTERY (7463)
2) MODULES OUTLET (PINK WIRE).
3) LED OUTLET.
4) ENGINE IMMOBILISATION.
NEUTRAL TIME OF ACTIVATION – EXTERNAL SENSOR EXCLUSION – WINDOWS CLOSURE LOCKING –COMFORT.
The neutral time of activation has a length of about 45 seconds and it is signalled from the Led switching on
with fix light. During the first 25 seconds of neutral time of arming it is possible to exclude the external
sensors and to stop the vehicle’s windows raise pressing on the transmitter’s 2 button (the windows closure
is subordinate to the installation of a power windows module or to the comfort function on the vehicle).
NOTE: THE EXCLUSION OF THE SENSORS AND OF THE W INDOWS RAISE IS LIMITED TO ONLY ONE ARMING CYCLE OF
THE ALARM.
EXCLUSION OF THE SIREN SOUND
To isolate the siren sound and allow the alarm signalling only through the direction indicator lights it is
necessary to follow this procedure:
a. With the system disarmed, turn the ignition key to ON – the led switches on for 0,5 seconds.
b. During these 0,5 seconds press on the transmitter n. 2 button – the led will switch off immediately.
The siren and the additional external siren will be excluded for the next arming cycle of the alarm
system.
To activate again the alarm audible signalling it is sufficient to disarm and to arm again the alarm
system.
SYSTEM ARMED AFTER THE INHIBIT TIME.
At the end of the neutral time of arming (about 45”), the security system is completely armed and it is
ready to intervene if a sabotage or a theft attempt occurs. The condition of alarm completely armed is
signalled through the signalling Led, which in order to guarantee a low current consumption is
controlled with the following timing:
LED ON: 200MS
LED OFF: 4”
THE EVENTS WHICH COULD TRIGGER THE ALARM ARE THE FOLLOWING:
a) CUT THE SYSTEM’S WIRES.
b) ATTEMPT TO START THE VEHICLE’S.
c) CURRENT ABSORPTION (Function to be activated in the programming phase of the accessorial
functions).
d) ATTEMPT TO OPEN THE DOOR / REAR BOOT.
e) PANIC ALARM – press on the transmitter’s n.2 button. (Function to be activated in the
programming phase of the acces sorial functions).
f) BONNET OPENING.
g) EFFRACTION OF THE VEHICLE SIGNALLED THROUGH AN EXTERNAL SENSOR.
ALARM CYCLE
The alarm cycle consists of the activation of the siren (if not previously excluded) and the flashing of
the direction indicator lights of the vehicle (with timing 0,5” ON – 0,5” OFF) for a maximum of 30”.
If the siren sound has been excluded, the alarm will signal the alarm triggering with the direction
indicator lights flashing for a maximum of 30”.
NOTE: During the alarm signalling the led will light fix.
It is possible to stop the alarm cycle, without disarming the system, pressing on the transmitter’s n.2
button. In this condition the optical / audible signalling stops and the system is in the “NETURAL TIME
BETWEEN FOLLOWING ALARM” condition.
In order to set a limit to the acoustic pollution, the DOOR PIN SWITCH, ABSORPTION SENSOR and
EXTERNAL SENSORS inlet has a limitation to 5 alarm cycles for each period of the system arming.
The count resets at the following disarming of the alarm system.
NOTE: THE IGNITION LIVE INLET AND THE CUT WIRES FUNCTION DO NOT HAVE ALARM LIMITATIONS.
NEUTRAL TIME BETWEEN FOLLOWING ALARMS
AT THE END OF EACH ALARM CYCLE THERE IS A NEUTRAL TIME (ABOUT 5”) WHERE THERE WILL BE ANY
REACTION TO THE ALAR M TRIGGERING CAUSE.
DURING THE NEUTRAL TIME BETWEEN FOLLOWING ALARMS THE SIGNALLING LED WILL SWITCH ON
WITH FIX LIGHT, THE BEGINNING OF THE NORMAL FLASHING IS GIVEN AT THE END OF THE NEUTRAL TIME.
ALARM SYSTEM DISARMING
The alarm can be disarmed pressing on the transmitter n.1 button (or through the PIN-CODE
emergency procedure).
Following this operation it is possible to have two different types of confirmation signalling.
DISARMING WITHOUT ALARM TRIGGERING CAUSE: if the system does not have detected any theft attempt
or effractions will give one optical / audible signalling which consists of three flashings of the direction
indicator lights and three audible signalling with high tone (BIP).
DISARMING WITH ALARM TRIGGERING CAUSE: if the system has detected one or more theft attempts or
effractions will give one optical / audible signalling which consists of 5 flashing of the direction indicator
lights and 5 audible high tone (BIP), followed (after an interval of about 2 seconds) by the indication of
the last alarm triggering cause detected (ALARM MEMORY). The indication of the last alarm
triggering cause consists of one differentiated optical / audible signalling.
1) ALARM FOR CURRENT ABSORPTION: 1 flashing of the direction indicator lights, of the Led and
1 audible signalling with low tone (BOP) at the same time of the optical signalling.
2) ALARM FOR STARTING ATTEMPT: 2 flashing of the direction indicator lights, of the Led and two
audible signalling with low tone (BOP) at the same time of the optical signalling.
3) ALARM FOR DOOR OPENING: 3 flashing of the direction indicator lights, of the Led and 3
audible signalling with low tone (BOP) at the same time of the optical signalling.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gemini 7463 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info