Bedienungsanleitung Gemini 7502 (Seite 3 von 13) (Englisch)

479839

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

INTRODUCTION

GEMINI 7503.

The 7503 system is a self-powered alarm control unit with built-in sensors and can be installed on cars

having a 12-volt battery with the negative pole earthed.

DESCRIPTION

- Self-powered compact alarm control unit, remote-controlled with a dynamic code.

- Blinker and universal control to operate the centralised door locks, electric windows and roof (for cars

equipped with the “pack-comfort” system).

- Boundary and volume protection.

- Controls for self-powered siren and supplementary siren (continuous sound).

- LED memory.

- Remote “panic” or car finder.

- Electrical engine immobilizer.

- Electronic emergency key with dynamic code (CDE2) and emergency Pin-code.

- Control unit functions programmable by means of remote control.

- Power supply sabotage sensor (only for version 7503).

7502. like 7503 without self-powering unit.

INSTALLATION TIPS

- Connect the power cable to the positive pole of the batter and the earth directly to the car frame.

- Always connect the Black alarm lead marked VM to the door pushbuttons.

- Always connect the Black alarm leads marked V to the bonnet pushbutton and the boot

pushbutton.

- On cars with catalytic converters, implement the electrical engine immobilizers by pressing the

fuel pump.

- If an ultrasound module is being used, position the capsules up on the RH and LH door jambs of the

front windshield and aim them toward the car’s interior, far from the air vents.

- Make the electrical connections and programme the accessory functions by remote control.

ELECTRIC CONNECTIONS

(REMOVE NEGATIVE POLE OF BATTERY AND RECONNECT IT ONLY AFTER ASSEMBLY IS COMPLETED)

FUNCTION WIRE COLOR

Earth

BLACK marked M

Positive pole of battery

BLACK marked R

Engine immobilizer 1 (max. 8A)

TWO BLACKs marked H

Positive pole under key

BLACK marked G

Turn indicators

TWO ORANGES

Door pushbuttons

BLACK marked VM

Bonnet and boot pushbutton

TWO BLACKs marked V

Positive pole of alarm activated (max. 700 mA)

PINK

External sensors input

GREEN-BLACK

Negative control for supplementary siren

BLACK marked GN

Centralised locks

YELLOW-BLUE,

RED-BLUE,

YELLOW-GREY,

RED-GREY,

YELLOW-BROWN,

RED-BROWN

NOTE : In the wiring harness of the 7503 there are two 2-way connectors and one 4-way connector.

The 2-way connectors must be connected to the electronic key socket (art.2390 or art.2325). If only the

LED (art. 2324) is used, use only the 2-way connector with the Red wire and the Black wire.

The 4-way connector serves to connect the ultrasound module or the hyperfrequency module or

external modules, if fitted.

ACCESSORY FUNCTIONS PROGRAMMABLE BY REMOTE.

FUNCTION PROGRAMMED AT FACTORY

1 SOUND SIGNALS ENABLED

2 PANIC ALARM / CAR FINDER PANIC FUNCTION ENABLED

3 POWER DRAIN DISABLED

4 ANTI-DISTRACTION – AUTOMATIC DOOR-LOCKING FUNCTION DISABLED

5 PASSIVE ACTIVATION OF SYSTEM DISABLED

6 SELECTION CENTRALIZED LOCK TIMES (0.5 / 6 SEC.) 0.5 SEC. SELECTED:

7 25-SECOND COMFORT CLOSURE COMMAND DISABLED

8 DOUBLE PULSE WHEN OPENING DISABLED

ENTERING THE PROCEDURE FOR PROGRAMMING THE ACCESSORY FUNCTIONS.

Disconnect the alarm with the transmitter. Open the car door (and keep it open). Turn the ignition key to

the ON position: the LED will turn on for 0.5 seconds. When the LED is on, press both keys on the remote.

To confirm activation of programming mode, there will be a high beep followed by a low beep. The system

is now in the programming mode and therefore it is awaiting commands that must be imparted by means

of the remote control keys. During programming the LED stays on.

VARIATION OF FUNCTION MODE.

Each selection will be confirmed by a LED signal:

IF YOU PRESS KEY 1 (TO ENABLE THE FUNCTION AND GO THE NEXT FUNCTION ) A HIGH BEEP WILL SOUND.

IF YOU PRESS KEY 2 (TO ENABLE THE FUNCTION AND GO THE NEXT FUNCTION ) A LOW BEEP WILL SOUND.

Key 1: Enabled

SOUND SIGNALS

Key 2: Disabled

Key 1: Panic function enabled

Car finder disabled

PANIC ALARM OR CAR FINDER

Key 2: Panic disabled

Car finder enabled

Key 1: Enabled

POWER DRAIN

Key 2: Disabled

Key 1: Enabled

ANTI-DISTRACTION – AUTOMATIC DOOR-LOCKING FUNCTION

Key 2: Disabled

Key 1: Enabled

PASSIVE ACTIVATION OF SYSTEM

Key 2: Disabled

Key 1: 6-sec time enabled

CENTRALIZED LOCK TIMES

Key 2: 0.5 sec time enabled

Key 1: Enabled

COMFORT COMMAND

Key 2: Disabled

Key 1: Enabled

DOUBLE PULSE WHEN OPENING

Key 2: Disabled

EXITING ACCESSORY FUNCTION PROGRAMMING PROCEDURE.

You can exit the programming procedure at any time by turning the ignition key to the OFF position.

At this point, the changes will be memorized and unchanged function modes will be confirmed.

However, if you decide to program all the functions, the system will automatically exit the

programming function. In any event, after the procedure is completed, the system will signal the end

of programming the accessory functions with two low beeps and a high beep and the LED will turn

off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7502 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info