Bedienungsanleitung Gemini 7590T (Seite 2 von 9) (Englisch)

479862

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

TOTAL ALARM ARMING

The alarm can be activated by pressing key 1 on the remote or by inserting the

electronic key into the appropriate socket.

The operation is confirmed by an acoustic signal and a visual signal consisting

of one flash of the turn indicators lasting approximately one second.

During the flash, the following functions are enabled:

-Module output (PINK wire, +A).

-Led output.

-Engine immobilizer.

-Activation of door-locking control (with the timing selected in programming

phase).

Neutral activation time lasts approx. 35” and it is indicated by the continuous

light of the LED. This time interval allows the user to get out of the vehicle

without causing false alarm conditions. During the first 25” of the neutral time, it

is possible to cut out the external sensors and stop the windows' upward travel

by pressing key no. 2 on the remote (Note: the stop window function requires

the installation of a special module see art. 2344 or the existence of the

COMFORT function in the car).

The activation of said functions (Cutting out the external sensors / stopping

window upward travel / comfort) is indicated by a brief flash of the turn

indicators.

sensor cutout is limited to a single alarm activation cycle.

Turn the ignition key to “ON” position

The status will stay on for 0,5 seconds. During this time, push the button

N°2 of the transmitter.

Go away from the vehicle and push the button N°1 of the transmitter.

NEUTRAL TIME, SENSOR EXCLUSION , STOPPING WINDOW

UPWARD TRAVEL AND COMFORT FUNCTION

NOTE:

If the electronic key is used, all the functions described under points a), b) and

c) will be activated, whereas d)ACTIVATION OF DOOR-LOCKING CONTROL

will not occur (enabling the user to get out of the vehicle).

Moreover, by using the electronic key, a car entry time of approximately 10

seconds will be generated to allow the user to get into the car and deactivate

the alarm system with the electronic key without creating a false alarm.

While the user gets into the car, entry time is indicated by the continuous light of

the LED.

This function allows the user to arm the alarm system, excluding the siren

sound in case of a theft attempt.

To exclude the siren, proceed as follows:

The alarm will be armed with the optical and acoustic signals, which, as

previously described, will be not activated in case of a theft attempt.

the siren sound exclusion is bound to the single arming cycle.

ARMING WITH SIREN SOUND EXCLUSION

NOTE:

PAG . 2

PAG . 3

INTRODUCTION

FUNCTIONS

The 7590 system is a alarm control unit with built-in sensors and can be

installed on cars having a 12-volt battery with the negative poleearthed.

GENERAL NOTE FOR INSTALLATION

Dear installer, this manual has been conceived and written keeping in

mind the complete system. Therefore some functions, electrical

connection and other can be present in one alarm version and lack to

another.

In order to avoid useless repetitions in the manual, before installing the

available alarm, you are kindly requested to verify its version and then

follow the suitable instructions.

Furthermore, in order to carry out correctly the various procedures

required, we remind you to make and to verify very carefully all electrical

connections, IN PARTICULAR THE BASIC CONNECTIONS:

Device power supply (positive and earth)

Positive under key (+15/54)

Door switch

Bonnet or Trunk switch

Arming and disarming of the alarm system with transmitters having

random rolling code.

Electrical engine immobilizer by passive arming.

Double engine immobilizer.

Blinker.

Sirene sound intermittent or continuous (programmable).

Perimetric protection.

Volumetric protection (combined with an ultrasonic or hyperfrequency

module, excludable from arming).

Control for CDL, electrical widows and sun roof (vehicles equipped with

the system “Pack-comfort”).

Alarm memory indicated by optic/acousticl signals.

“PANIC” or “BOOT OPENING” function (programmable).

Current absorption sensor (programmable).

Anti distraction function (programmable).

Control for self-powered siren or supplementary siren.

Emergency disarming by PIN-CODE.

Garage function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7590T Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info