PAG. 12
PAG. 13
EMERGENCY DISARMING BY PIN-CODE
The procedure for emergency disarming by pin-code is the following.
Kindly note that the standard pin-code programmed is 1-1-1-1.
The same number used for pin-code programmation ( 5-4-6-7) has been used
also for emergency disarming example.
! Cause an alarm condition.
! Leave the alarm triggering for the standard timing (about 30 seconds) and
wait for the “inhibit time between two alarm signalling”
! During the inhibit time the LED remain steadly ON for about 5 seconds; Turn
the ignition key in “ON” position.
! LED switch “OFF” showing “the emergency procedure” entry
! Turn the ignition key in "OFF" position.
! After about 4 seconds the first 9 flashing sequence starts.
At the fifth LED flashing (corresponding at Number 5, first digit of the pin-
code) turn the ignition key in “ON” position (then turn in “OFF” position) or
push the button on the LED.
! The LED will be switch OFF for about 4 seconds than a new 9 flash
sequence will start.
At the fourth LED flashing (corresponding at Number 4, second digit of the
pin-code) turn the ignition key in “ON” position (then turn in “OFF” position)
or push the button on the LED.
! The LED will be switch OFF for about 4 seconds than a new 9 flash
sequence will start.
At the sixth LED flashing (corresponding at Number 6, third digit of the pin-
code) turn the ignition key in “ON” position (then turn in “OFF” position) or
push the button on the LED.
! The LED will be switch OFF for about 4 seconds than a new 9 flash
sequence will start.
At the seventh LED flashing (corresponding at Number 7, fourth digit of the
pin-code) turn the ignition key in “ON” position (then turn in “OFF” position)
or push the button on the LED.
If the code is right,the end of the emergency disarming by pin-codet will be
indicated by the alarm with visual/acoustic signalling.
Vice versa, if the inserted numbers are wrong, the alarm will start triggering
again.
In this case, repeat all procedure.
PROGRAMMING NEW PIN-CODE
The procedure to program pin-code is specified here below.
It is better to personalize the code as customer has required.
In this example, supposing that the pin-code is 5-4-6-7.
! With all the vehicle door close, unlock the alarm by using the vehicle original
radio control.
! Turn the ignition key in “On”position; the alarm will blink for a short time (0,5
sec.).
During this period, push the button of the LED.
The alarm will confirm that the programming has been enabled with a l,ong
acoustic signal with high tone and one short acoustic signals with low tone.
! Turn the ignition key in “OFF” position.
! After a four second pause, state led will start with the first sequence of
flashes.
At the fifth LED flashing (corresponding at Number 5, first digit of the pin-
code) push the button on the LED or turn the ignition key in “ON” position for
one second.
Turn the ignition key in “OFF” position.
! After a four second pause, state led will start with a new sequence of
flashes.
At the fourth LED flashing (corresponding at Number 4, second digit of the
pin-code) push the button on the LED or turn the ignition key in “ON” position
for one second.
Turn the ignition key in “OFF” position.
! After a four second pause, state led will start with a new sequence of
flashes.
At the sixth LED flashing (corresponding at Number 6, third digit of the pin-
code) push the button on the LED or turn the ignition key in “ON” position for
one second.
Turn the ignition key in “OFF” position.
! After a four second pause, state led will start with a new sequence of
flashes.
At the seventh LED flashing (corresponding at Number 7, fourth digit of the
pin-code) push the button on the LED or turn the ignition key in “ON” position
for one second.
Turn the ignition key in “OFF” position.
The alarm system will indicate the end of the PIN-CODE personalizing
procedure by one state LED flash.
ATTENTION: If during one of four “nine flashing” sequences, no number is
confirmed (value “0”), at the end of 9th flash, the PIN-CODE saving to memory
procedure, will stop automatically.
