Bedienungsanleitung Gemini 7672 (Seite 3 von 5) (Englisch)

479868

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

PAG. 4

PAG. 5

In order to restore the normal operation of the alarm system, proceed as

follows:

! Push the TAG button, until the LED is illuminated.

! Open and close the driver side door.

! Put twice the electronic key in the receptacle (alarm arming/disarming).

ALARM SIGNALLING DELAY

The system has a delay response of 15 seconds between the robbery

detection and its signaling (optical/acoustical signals).

This delay, or pre-alarm, has been programmed to avoid involuntary but

possible “false alarms” which can occur when the user opens the door or he

enters in the vehicle, while the system is still armed (no transmission by the

TAG card).

The pre-alarm condition will be indicated by the constant turning on of the led

and, if the system remains armed 8 seconds after the attempt, a loud acoustic

signal will be sent out. If the system has not been disarmed, within the pre-

alarm period, usual optical/acoustical signals will be activated.

NOTE: during the pre-alarm signaling, the alarm cycle and the neutral

time between two alarm signaling, just the reception of the TAG signal,

will disarm the system without any door being open.

ALARM MEMORY

When disarming the alarm, if five turn signal flashes and five beep signals

occur, it is possible to identify the cause generating the alarm condition.

To do this, turn the ignition key to “ON” and look at the vehicle status LED.

The LED will be blink, shown the last alarm condition.

The cause of the alarm will indicate for five times, and this indication can be

interrupted by turning the ignition key to “OFF” position.

The possible alarm signalling are indicated in the table below.

LED SIGNAL

CAUSE OF THE ALARM

LED OFF (2 seconds) LED ON (400mS)

Absorption sensor

Positive under key (+15/54)

Trunk, hood volumetric sensors

External magnetic contact

Door switches

Cut wires

PROGRAMMING THE ALARM SYSTEM

Has been prevously programmed with standard configuration during

manufacturing procedure by Gemini.

The basic configuration can be modified in any moment and has the following

programmable functions:

K Acoustic signalling for arming and disarming (enabled).

L Current absorption sensor (disabled).

M Anti-hijacking function (disabled).

N Optictic signalling for arming and disarming (enabled).

Cutting off the power supply of vehicle electrical equipment, no programmed

functions are changed.

To modify the alarm programming, see at the indications repoted below:

! With the alarm system disarmed and the driver side door closed, turn the

ignition key in “ON” position.

! The LED will blink for a short time (about 1 second).

! During this period, insert the electronic key in the receptacle.

! Starting of programming procedure is indicated by one high tone and two

loud tones; if this does not occur, repeat the procedure from the beginning.

NOTE: this procedure must be carried out entirely. Indeed, by changing

the position of the vehicle ignition key, the function is confirmed, while

passing at the next one.

! In order to keep unchanged the operating state, turn the ignition key to

“OFF” and then back to “ON”. A loud acoustic signal will confirm the

operation.

! To change the operating state, put once the electronic key in the specific

receptacle.

! In both cases, the alarm will pass at the next function.

! Turn the ignition key to “OFF” (if not yet done, to keep unchanged the

operating state).

! The end of this procedure will be indicated by two acoustic signals, one

with loud tone and one with high tone.

Acoustics signalling

Current absorption sensor

Anto-hijacking function

Optical signalling

Vehicle ignition key - Confirm

Electronic key - Modify

Vehicle ignition key - Confirm

Electronic key - Modify

Vehicle ignition key - Confirm

Electronic key - Modify

Vehicle ignition key - Confirm

Electronic key - Modify

FUNCTION STATE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7672 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info