Bedienungsanleitung Gemini 822 (Seite 3 von 8) (Englisch)

479879

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

PAGE 04 - USER MANUAL USER MANUAL - PAGE 05

2.6 - SYSTEM DISARMING

2.7 - ALARM MEMORY

Press the unlock button on the original radio control of the vehicle; s

(2.7) for possible causes and signaling.

ystem disarming is confirmed by

two siren chirp (if feature has been modified) and two flashes of the turn indicators

An alarm condition will be signalled by five audio signals and five flashes from the turn indicators.

See relative paragraph

If during system disarming, the turn indicators flash 5 times and 5 audio signals (if feature has been

modified) are heard, the cause of the last alarm can be identified by the LED memory.

Turn the ignition key “ON” and look at the vehicle status LED; the blinking will indicate the last alarm

condition.

The visual signals will be repeated 3 times.

To interrupt, turn ignition key “OFF”.

The alarm trigger signals and relative causes are indicated in the table below

3.0 - NEW PIN-CODE PROGRAMMING

The procedure to program pin-code is specified here below as previously described, it is better to

personalize as customer has required.

In this example reported below, supposing that the pin-code is 5-4-6-7.

During PIN-CODE programming phase, if flashes are more than 9, this phase will be

invalid and the system will close the procedure.

With the system being disarmed, open the driver side door and bonnet and keep they open.

Turn the vehicle ignition key in “ON”-“OFF”-“ON”-“OFF”-“ON”-“OFF”-“ON” position; after the fourth

commutation, let the vehicle ignition key to “ON.

The indicators will flash once and two high pitched signals will sound (one brief and the other

longer) to indicate the system is in the programming mode.

Turn the vehicle ignition ket to “OFF” position.

After a three second pause, state LED will start with the first sequence of 9 flashes.

At the fifth LED flashing (corresponding at nr.5, first digit of the PIN-CODE), push and release the

button on the status LED.

After a three second pause, state LED will start with a new sequence of 9 flashes.

Athe fourth LED flashing (corresponding at nr.4, second digit of the pin-code) push and release the

button on the status LED.

After a three second pause, state LED will start with a new sequence of 9 flashes.

At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the

button on the status LED.

After a three second pause, state LED will start with the last sequence of 9 flashes.

At the seventh LED flashing (corresponding at nr.7, fourth digit of the pin-code) push and release

the button on the status LED.

No audio/visual signal will indicate the end of the procedure.

LED FLASHES ALARM CAUSES

Nr. OF ALARM

CYCLES

Starting attempt (+15/54)

Doors opening*

Bonnet opening

Boot opening

Volumetric or external sensor

Wire tampering

LED ON (1 second)LED OFF (2 seconds)

* Entry delay of 4 sec.

4.0 - EMERGENCY DISARMING BY PIN-CODE

The procedure for emergency disarming by pin-code is following, reported below.

Kindly note that the standard pin-code programmed is of the four digit 1-1-1-1.

The same number used for pin-code programmation (5-4-6-7) has been used also for emergency

disarming example.

During PIN-CODE disarming phase, if flashes are more than 9, the procedure will be

.interpret as a theft attemp

Cause an alarm condition.

Leave the system triggering for the standard alarm timing (about 30 seconds) and wait for the

“inhibit time between two alarm signalling” (LED switched off for 5”).

During this period push and release the push-button of the status LED.

the “emergency procedure disarming” and the LED will start

flashing.

At the fifth LED flashing (corresponding at nr.5, first digit of the pin-code), push and release the

button on the status LED.

After a three second pause, state LED will start with a new sequence of 9 flashes.

At the fourth LED flashing (corresponding at nr.4, second digit of the pin-code), push and release

the button on the status LED.

After a three second pause, state LED will start with a new sequence of 9 flashes.

At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the

button on the status LED.

After a three second pause, state LED will start with a new sequence of 9 flashes.

At the seventh LED flashing (corresponding at nr.7, fourth and last digit of the pin-code) push and

release the button on the status LED.

If the code is right, the end of the emergency disarming by pin-code will be indicated by the alarm

system with visual/acoustic signalling.

Vice versa, if the inserted numbers are wrong, the alarm system will start triggering again; in this

case, repeat all procedure.

From now and on the system is in

5.0 - WARRANTY CONDITIONS

This apparatus is guaranteed against all defects of fabrications for a period of 24 month from the

installation date shown on this warranty coupon, taking into consideration the 1999/44/CE.

Therefore, you are kindly requested to fill entirely the guarantee certificate included in this booklet and

to NOT REMOVE the guarantee label from the device.

Missing or tearing of this label, missing of one part of guarantee certificate or missing of the enclosed

sale document, will invalidate the guarantee.

The guarantee is valid exclusively to Gemini TechnologiesS.p.A.Authorized Service Centers.

The manufacturer will decline any responsibility for any eventual malfunctions of the device, or

electrical plant damages of the vehicle, due to improper installation, use or tampering.

This alarm system has exclusively a deterrent function against eventual thefts.

Gemini 822 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 822

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info