Bedienungsanleitung Gemini 861 (Seite 4 von 8) (Englisch)

479882

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

3.0 - NEW PIN-CODE PROGRAMMING

The procedure to program pin-code is specified here below as previously described, it is better to

personalize as customer has required.

In this example reported below, supposing that the pin-code is 5-4-6-7.

PAGE 06 - USER MANUAL

To carry out the operation successfully, make sure the required electrical connections

(door push-button and positive under key) are complete.

During PIN-CODE programming phase, if flashes are more than 9, this phase will be

invalid and the system will close the procedure.

With the system being disarmed, open the driver side door and keep it open.

Turn the vehicle ignition ket to “ON” position.

The status LED will be turned on for one second; during this period, push simultaneously the two

buttons of the remote contol with embossed the padlocks.

and the LED will lighted on.

Push simultaneously the two buttons of the remote contol with embossed the padlocks; the LED will

be turned off.

Turn the vehicle ignition ket to “OFF” position.

After a four second pause, state LED will start with the first sequence of 9 flashes.

At the fifth LED flashing (corresponding at nr.5, first digit of the PIN-CODE), push and release the

button on the status LED.

After a four second pause, state LED will start with a new sequence of 9 flashes.

Athe fourth LED flashing (corresponding at nr.4, second digit of the pin-code) push and release the

button on the status LED.

After a four second pause, state LED will start with a new sequence of 9 flashes.

At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the

button on the status LED.

After a four second pause, state LED will start with the last sequence of 9 flashes.

At the seventh LED flashing (corresponding at nr.7, fourth digit of the pin-code) push and release

the button on the status LED.

The system will indicate the end of the procedure by two acousic signal with low tone and one with

high tone.

fter this procedure, two acoustic signals will be sent out one with acute tone and the other with

loud tone

4.0 - EMERGENCY DISARMING BY PIN-CODE

The procedure for emergency disarming by pin-code is following, reported below.

Kindly note that the standard pin-code programmed is of the four digit 1-1-1-1.

The same number used for pin-code programmation (5-4-6-7) has been used also for emergency

disarming example.

During PIN-CODE disarming phase, if flashes are more than 9, the procedure will be

.interpret as a theft attempt

Cause an alarm condition.

Leave the system triggering for the standard alarm timing (about 30 seconds) and wait for the

“inhibit time between two alarm signalling” (LED switched off for 5”).

During this period push and release the push-button of the status LED.

the “emergency procedure disarming”.

After about 4 seconds the first 9 flashing sequence starts.

At the fifth LED flashing (corresponding at nr.5, first digit of the pin-code), push and release the

button on the status LED.

The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.

At the fourth LED flashing (corresponding at nr.4, second digit of the pin-code), push and release

the button on the status LED.

The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.

At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the

button on the status LED.

The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.

At the seventh LED flashing (corresponding at nr.7, fourth and last digit of the pin-code) push and

release the button on the status LED.

If the code is right, the end of the emergency disarming by pin-code will be indicated by the alarm

with visual/acoustic signalling.

Vice versa, if the inserted numbers are wrong, the alarm will start triggering again; in this case,

repeat all procedure.

From now and on the system is in

This function is used ONLY if “system self-rearming” or “passive arming” functions

have been programmed.

This function is used when the alarm disarming is required, e.g. for maintenance, without any

intervention to the previous programming

o restore normal operating of programmed functions, arm the alarm via the control

For procedure activation follow the indications reported below:

Arm the system and wait for the end of arming neutral time.

Put the electronic key into the specific receptacle.

Three acoustic signals of the siren and three optical signals of turn signals will indicate the system's

disarming and the above mentioned function deactivation.

remote

USER MANUAL - PAGE 07

5.0 - GARAGE FUNCTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 861 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 861

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info