Bedienungsanleitung Gemini 862 (Seite 6 von 8) (Englisch)

479883

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

PAGE 10 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 11

9.0 -

In this chapter various functions of the system are concisely described; for programming please follow

the instruction given in paragraph “SYSTEM PROGRAMMING”.

This function activates acoustic signals during system arming (2) and disarming (3).

According to the programming, this function allows to:

Press the “panic button” of radio control in order to activate the siren for 30” (remote controlled

panic alarm).

Being the system armed, press the “panic button” of radio control in order to activate for few

seconds the siren and the turn signals (car finder).

This function activates the system anytime a voltage sudden change in the vehicle's electrical circuit is

occurring.

B current

This function allows vehicle’s protection in case the user disarms accidentally the system.

Thus, the system will be automatically rearmed after 35”, if no intervention on the vehicle is done (i.e.

door opening, engine start).

Function that allows to have the system active 35” after the engine switching “OFF”

Function that allows to select the CDL closure time.

This function allows activating the comfort control (window closing) when the system is armed.

This function activates twice the opening control and it is used on vehicles with diversified opening.

This function, once connected, can activate the supplementary siren or open the trunk (remote control

button with embossed trunk icon).

This function activates for few seconds the siren, if a door is open being the system armed.

This function activates the optical signaling, according to the connection. It should be activated in

some particular vehicles on which connection is made directly on the wire from the “hazard” button..

9.1 - ACOUSTIC SIGNALLING

9.2 - REMOTE CONTROLLED PANIC ALARM

9.3 - CURRENT ABSORPTION SENSOR

9.4 - SYSTEM SELF-REARMING AND DOOR LOCKING

9.5 - PASSIVE ARMING

9.6 - CENTRAL DOOR LOCKING SETTING TIME

9.7 - COMFORT CLOSURE CONTROL

9.8 - DOUBLE IMPULSE IN OPENING

9.9 - SUPPLEMENTARY SIREN OUTPUT OR BOOT OPENING

9.10 -

9.11 - OPEN DOOR SIGNALING DURING ARMING TIME

9.12 - OPTICAL SIGNAL ACTIVATION SELECTION

PROGRAMMABLE FUNCTIONS DESCRIPTION

efore activating of the absorption sensor, it is suggested to consult the specific rules being in

force in your country (noise pollution)

Together with the system self-rearming, the automatic door locking of the vehicle is done when

running.

Being closed all the doors of the vehicle, turn the ignition key to “ON”; after 20”, all doors will be locked.

By turning the ignition key to “OFF”, all doors of the vehicle will be automatically unlocked

Depending on connection, this function can activate the output for the siren (continuous tone) or for

the horn (intermittent tone

NEGATIVE OUTPUT SELECTION (DURINGALARM) FOR HORNS OR ADDITIONAL SIREN

If you open a door during this period, the procedure will be interrupted till the door is closed

10.0 - SYSTEM PROGRAMMING

The system has been previously programmed with standard configuration during manufacturing

procedure by Gemini.

With the system being disarmed, turn the vehicle ignition key to “ON” position.

The status LED stay on for one second; during this time, push together the two buttons of the

remote control with embossed the padlocks (button 1or 2).

Starting of programming procedure is indicated by two acoustic signals, one with high tone and one

with loud tones, furthermore the status LED turns ON.

To able and disable the functions, follow the below table, take into consideration that every time the

push button of transmitter is pressed, the system goes to the following function.

(button 1 or 2), .

For programming modification proceed as follows

Furthermore,

according to the button being pressed two different acoustic signals are emitted

Pay attention to not modify the functions which have been programmed during the

installation.

Once the last function has been programmed, the alarm will confirm that the programming has

been disabled with two acoustic signals with low tone, one acoustic signal with high tone,

Turn the vehicle ignition key to “OFF” position.

furthermore the LED will be turned off

When the optical pulse signaling feature is activated, the blinkers will ONLY emit optical

signals during an alarm cycle.

9.13 - DOORS PUSH-BUTTONS POLARITY SELECTION

This function modifies the alarm input signal (positive or negative) according to the signal from the

door’s button.

FUNCTION STATUS BUTTON “1” BUTTON “2”

Arming/disarming acoustic signalling

Panic alarm or car finder

Current absorption sensor

System self-rearming

System passive arming

Setting of opening/closing time (1” or 6”)

25” comfort closure

Lock double impulse in opening

Selection of supplementary siren or boot

opening by remote

Selection of continuous sound

(supplementary siren) or alternate

(vehicle’s claxon)

“Doors opened” signalling during system

arming

“Standard” or “impulse” optic signalling

activation

Selection of doors input polarity

By turning the ignition key to “OFF” in any moment of the programming procedure, the

latter will stop and successive functions will remain unchanged.

Enable

Enable panic

Enable

Enable 6”

Enable

Enable boot

opening

Elternate sound

(vehicle’s claxon)

Enable

Enable “impulse”

Enable positive

polarity

Disable

Enable car finder

Disable

Enable 1”

Disable

Enable

supplementary

siren

Continue sound

(siren)

Disable

Enable

“standard”

Enable negaive

polarity

Enabled

Disabled

Selected 1”

Disabled

Enabled

supplementary

siren

Enabled continue

sound

Disabled

Enabled

“standard”

Enabled negative

polarity

Gemini 862 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 862

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info