Bedienungsanleitung Generac MMG175DI4 (Seite 45 von 68) (Englisch)

685346

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Maintenance

33722 D MMG130DI4/175DI4/205DI4 Operating Manual 39

* Replace primary air cleaner when dust valve restriction indicator gauge shows a vacuum of 25 in. H

** Change the oil and oil filter after the first 100 hours, then every 500 hours. If not using John Deere Plus 50 II

engine oil, the interval must be decreased to every 250 hours.

ENGINE BREAK-IN REQUIREMENTS

Note: During the first 20 hours of operation, avoid long periods of no load or sustained maximum load operation. If

the generator is to run for longer than five minutes without a load, shut the generator down.

John Deere engines are supplied with engine break-in oil from the factory. Extra care during the first 100 hours of

engine operation will result in better performance and longer engine life. DO NOT exceed 100 hours of operation

with the break-in oil. Operate the engine at heavy loads (60-90% of maximum) as much as possible. If the engine

has spent significant time at idle, constant speed(s), and/or light load, or if makeup oil is required, a longer break in

period may be needed. Refer to the engine operator’s manual for a full description of necessary procedures on the

addition of break-in oil and extension of the break-in period. For more information on regular maintenance intervals,

refer to Basic Maintenance Schedule - John Deere Engine.

RESETTING THE MAINTENANCE ALARMS

The Power Zone™ controller will display a warning message when the unit is due for maintenance or service. The

maintenance or service interval is set at 250, 500 and 3000 hours of engine running time. Once the unit has been

serviced, the appropriate maintenance alarm reminder needs to be reset. The following procedure demonstrates

how to reset the maintenance alarms:

1. With the unit shut down, move the control power switch to ON (I). After initialization, the controller will toggle

automatically to the Home screen.

2. Press any directional arrow (▲, ►, ▼, ◄) to enter the maintenance screens.

3. Press the Enter () button and the Engine Stop/Reset (O) button simultaneously. The next screen will dis-

play the Configuration menu.

4. Press  to move the cursor (blue highlighted text) down to the “Maintenance” group.

5. Press ► to access the sections. Press  to highlight the “Maintenance” section.

6. Press ► to access the parameters and highlight the maintenance alarm that needs to be reset.

7. Press the Enter () button to select the editable parameters. The cursor will highlight “Not Reset” under the

selected maintenance alarm. Press  to highlight “Reset”.

8. Press the Enter () button to reset the selected maintenance alarm.

9. To perform additional maintenance alarm resets, repeat steps 6 - 8.

Note: If the selected maintenance alarm does not need to be reset, press the  button to highlight “Not Reset” and

press the Enter () button return to the parameters section.

Replace Air Cleaner Elements 

Replace Alternator and Fan Belts 

Check Fuses 

Add Coolant 

Check Electrical Wiring and Connections 

Item Daily

250

Hrs.

500

Hrs./12

Months

3000

Hrs./ 36

Months

Required

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Generac MMG175DI4 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info