Bedienungsanleitung General Electric AEM10 (Seite 5 von 48) (Englisch, Französisch, Spanisch)

502923

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

GEAppliances.com

In the case of a power outage or interruption, the

unit will automatically re-start in the settings last

used after the power is restored. If the Delay 1–24hr

feature was set, it will resume countdown. You may

need to set a new time if desired.

Power Outage Recovery Feature

Cool Mode

Use the Cool mode at Low, Med, High or Auto Fan

Speed for cooling. Use the Temperature Increase ▲

/ Decrease ▼ pads to set the desired temperature

between 64°F and 86°F in 1°F increments.

An electronic thermostat is used to maintain the room

temperature. The compressor will cycle on

and off to keep the room at the set level of comfort.

Set the thermostat at a lower number and the indoor

air will become cooler. Set the thermostat at a higher

number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to a Cool setting or if turned from a fan

setting to a Cool setting, it may take approximately

3 minutes for the compressor to start and cooling to

begin.

Cooling Descriptions

For Normal Cooling—Select the Cool mode and

High or Med fan with a middle set temperature.

For Maximum Cooling—Select the Cool mode

and High fan with a lower set temperature.

For Quieter and Nighttime Cooling—Select the

Cool mode and Low fan with a middle set

temperature.

Energy Saver Mode

Controls the fan.

ON—The fan will cycle on and off with the

compressor. This results in wider variations of room

temperature and humidity. Normally used when the

room is unoccupied. NOTE: The fan may continue to

run for a short time after the compressor cycles off.

OFF—The fan runs all the time, while the compressor

cycles on and off.

Fan Only Mode

Use the Fan Only Mode at Low, Med or High fan

speed to provide air circulation and filtering without

cooling. Since fan-only settings do not provide

cooling, a Set temperature cannot be entered. The

room temperature will appear

in the display.

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Set to Auto fan speed for the fan speed to

automatically set to the speed needed to provide

optimum comfort settings with the set temperature.

If the room needs more cooling, the fan speed

will automatically increase. If the room needs less

cooling, the fan speed will automatically decrease.

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Auto Fan Speed

Remote Control

n To ensure proper operation, aim the remote

control at the signal receiver on the air

conditioner.

n Make sure nothing is between the air conditioner

and the remote control that could block the

signal.

n The remote control signal has a range of

up to 20 feet.

n Make sure batteries are fresh and installed

correctly as indicated on the remote control.

n Remote contains a magnet allowing it to attach

to metal surfaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric AEM10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info