Bedienungsanleitung General Electric CFCP1 (Seite 20 von 136) (Englisch, Französisch, Spanisch)

503063

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Installation Instructions

LOCATING THE ANTI-TIP

FLOOR BRACKET (cont.)

Preferred Installation –

Wood

Preferred Installation –

Concrete

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #2 –

Wood Floor

Minimum Acceptable #3 –

Concrete Floor

Figure 2 – Acceptable Screw Placement

Locations

CONCRETE Wall and Floor Construction:

• Anchors required (not provided):

4 each 1/4” x 1 1/2” lag bolts

4 each 1/2” O.D. sleeve anchors

• Drill the recommended size holes for the

anchors into the concrete at the center of

the holes marked in Step 2.

• Install the sleeve anchors into the drilled

holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the locator

template from the floor.

• Install the lag bolts through the anti-tip floor

bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes

identified in Fig. 1. Drill an angled 1/8” pilot

hole (approx. as shown in Fig. 3) in the center

of each hole.

• Mount the anti-tip floor bracket using the

Minimum Acceptable Installation #1, as

illustrated in Fig. 2.

ANTI-TIP BRACKET INSTALLATION

WOOD Wall and Floor Construction:

• Drill the appropriate number of 1/8” pilot

holes in the center of each floor bracket hole

being used (a nail or awl may be used if a drill

is not available) AND remove the locator

template from the floor.

• Mount the anti-tip floor bracket by fastening

the 2, or preferably 4, #10-16 hex-head

screws tightly into place as illustrated in

Figure 3.

POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

Before pushing the refrigerator into the

opening, plug the power cord into the

receptacle and connect waterline (if equipped).

Check for leaks.

Locate the refrigerator’s RH side and move

back approximately in line with the RH side of

the cabinet opening, W. This should position the

anti-tip floor bracket to engage the anti-tip

base bracket on the refrigerator.

Gently roll the refrigerator back into the cabinet

opening until it comes to a complete stop.

Check to see if the refrigerator front lines up

with the cabinet front face. If not, carefully rock

the refrigerator forward and backward until

engagement occurs and you notice that the

refrigerator is fully pushed up against the rear

wall.

OPTIONAL: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip

brackets, while also aligning the refrigerator

front with the cabinet front face.

Figure 3 – Attachment to

Wall and Floor

NOTE:

If you pull the refrigerator out and away from the

wall for any reason, make sure the anti-tip floor

bracket is engaged when the refrigerator is pushed

back against the rear wall.

Rear RH Corner of

the Refrigerator

Floor

Wall

Plate

Stud

Floor

Bracket

2 Screws

Must Enter

Wood or

Metal Stud

Wall

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric CFCP1 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info