Bedienungsanleitung General Electric DDE7608M (Seite 5 von 16) (Englisch)

646520

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

~F.brie Care Selections

Push a button to select the proper heat for

your load.

Should be used with cycles indicated ●

Automatic,

Fabric Care

Automatic

Perm Press and

Timed

Selections

Regular Cycle

Knits Cycles

Cycles

Cottons

Hiah

Heat

●

Perm Press

Medium Heat

●

Knits/Delicates

Low Heat

●

Fluff

No Heat

●

Extra Care Cycle

Select End of Cycle Signal, if

(Operates only with Automatic,

desired. (See below. )

Perm Press& Knits Cycles. )

Turn Cycle Selector to desired

//’

Turn to ON if desired. To minimize

cycle setting. The selector may be

wrinkles set in the clothes, the Extra

Care cycle provides approximately

turned in either direction.

15 minutes of no-heat tumbling

Press PUSH TO START button

after the clothes are dry.

to start dryer. (Opening the door

Use End-of-Cycle Signal. Signal

during operation stops

the dryer. To

will sound at five-minute intervals

re-start, close the door and press

to remind you to remove the clothes.

the START button. )

End-of-Cycle Signal

(Operates with any cycle.)

MED

The Signal control can be set

anywhere between OFF and

LOUD, depending on desired

sound level. The signal will sound

just before the end of the cycle to

remind you to remove the clothes.

To stop signal while sounding, turn

Signal control to OFF or advance

Cycle Selector to OFF.

The Signal should always be used

when drying Polyester Knits or

Permanent Press items which

should

be removed as soon as the

dryer stops to help prevent setting

of wrinkles.

The signal should also be used with

the Extra Care Cycle.

Polyester Knits &

Permanent Press

drying tips

● DO NOT

OVERLOAD—

Garments being dried or

dewrinkled should tumble freely.

● REMOVE CLOTHES

PROM~LY—To help prevent

wrinkling, remove from the dryer

promptly at the end of the drying

cycles.

● PLACE ON

HANGERS—

Permanent Press and Polyester

Knit garments look best if placed

on hangers after drying.

What is the difference

between Mined &

Automatic drying?

Timed Drying

When using the TIMED CYCLES,

you select the number of minutes

you wish the dryer to run and it

turns off at the end of this time

period.

Automatic Drying

When using the Automatic Cycles,

the Electronic Sensor

Control

.p:~

system

continually senses the

~..

“Wel%e@

determines when they a;e dried to

your pre-selected setting, and

terminates the cycle automatically.

Refer to the CONTROLS SETTING

GUIDE for recommended settings.

The Cycle Selector will not advance

until clothes have reached a certain

degree of dryness.

Dryness selections guide for

the automatic cycles

Set to Middle Position

,,,

OFF

,,”

● For most normal loads

Set toward MORE DRY

● For loads that include heavy-

weight fabrics.

● If you desire to remove more

moisture.

Set toward LESS DRY

● For lightweight fabric loads.

● If you desire to remove less

moisture.

● For very small loads.

—

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric DDE7608M Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info