Bedienungsanleitung General Electric GFDR480 (Seite 21 von 144) (Englisch, Französisch, Spanisch)

646557

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Installation Instructions

TEST FOR LEAKS

Never use an open flame to test for gas leaks.

Check all connections for leaks with soapy solution

or equivalent.

Apply a soap solution. The leak test solution must

not contain ammonia, which could cause damage

to the brass fittings.

If leaks are found, close the valve, retighten the

joint and repeat the soap test.

Ground

Screw

ELECTRICAL CONNECTION

INFORMATION FOR GAS DRYERS (cont.)

ELECTRICAL CONNECTION

INFORMATION FOR GAS DRYERS

- Electrical Shock Hazard

WARNING

Plug into a grounded 3 prong outlet.

DO NOT remove ground prong.

DO NOT use an adapter.

DO NOT use an extension cord.

Failure to do so can result in death, fire or electrical

shock.

• Circuit – Individual properly polarized and grounded

15 or 20 amp circuit breaker or time-delay fuse.

•

Power Supply – 2-wire plus ground, 120 Volt,

single phase, 60 Hz, alternating current.

•

Outlet Receptacle –

Properly grounded

3-prong receptacle to

be located so the power

cord is accessible when

the dryer is in an installed

position. If a 2-prong

receptacle is present, it

is the owner’s responsibility to have a licensed

electrician replace it with a properly grounded

3-prong grounding type receptacle.

Ensure proper

ground exists

before use.

GROUNDING INSTRUCTIONS

This dryer must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of

least resistance for electric current. This dryer uses

a cord having an equipment-grounding conductor

and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed

and grounded in accordance with all local codes

and ordinances.

WARNING

Improper connection of the

equipment-grounding conductor

can result in a risk of electric shock. Check with a

qualified electrician, or service representative or

personnel, if you are in doubt as to whether the

appliance is properly grounded. DO NOT modify the

plug on the power supply cord. If it will not fit the

outlet, have a proper outlet installed by a qualified

electrician.

SAVE THESE INSTRUCTIONS

• Dryer must be electrically grounded in

accordance with local codes and ordinances,

or in the absence of local codes, with the latest

edition of the NATIONAL ELECTRICAL CODE,

ANSI/NFPA NO. 70 or CANADIAN ELECTRICAL

CODE, CSA C22.1. Check with a licensed

electrician if you are not sure that the dryer is

properly grounded.

•

If required by local codes, an external 18 gauge

or larger copper ground wire (not provided)

may be added. Attach to dryer cabinet with a

#8-18 x ½” sheet metal screw (available at any

hardware store) to rear of dryer as illustrated.

Open Gas

Valve

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric GFDR480 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info