Bedienungsanleitung General Electric PFE29 (Seite 29 von 47) (Englisch)

503105

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where

refrigerator will be placed, W.

Be sure to account for any countertop overhang,

baseboard thickness and any clearance desired.

Width, W, should not be less than 36”. The

refrigerator will be placed approximately in the

middle of this opening.

MATERIALS YOU MAY NEED (not included)

TOOLS YOU WILL NEED

Pencil

1/8” (3 mm) Drill Bit and

Electric or Hand Drill

Tape measure

5/16” (8 mm) Nut Driver

Lag Bolts

1/4” (6 mm) x 1-1/2” (38 mm)

Anchor Sleeves

1/2” (12 mm) OD

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

Drill Bit Appropriate for Anchors

AT-1

Baseboard

Thickness or

Countertop

Overhang

(Whichever Is

Larger) Plus

Any Desired

Clearance

Rear Wall

Front

RH Side

AT-2

LOCATING THE ANTI-TIP FLOOR

BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor

up against the rear wall, within W, and in line

with the desired location of the RH side of the

refrigerator (see Figure 1).

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with

the floor holes indicated on the template sheet,

approximately 15 ¼” from the edge of the sheet

or the RH side of the refrigerator.

Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.

NOTE:

,WLV5(48,5('WRXVHDWOHDVWVFUHZVWRPRXQW

the floor bracket (one on each side of the

anti-tip floor bracket). Both must be into either

the wall or the floor. Figure 2 indicates all the

acceptable mounting configurations for screws.

Identify the screw holes on the anti-tip floor

bracket for your configuration.

REFRIGERATOR

Figure 1 – Installation Overview

Base Bracket

on the

Refrigerator

2 Wall Holes

RH Side of

Refrigerator

Floor – Concrete

(2 Holes)

Floor – Wood

(2 Holes)

15 ¼”

Locator Template

Sheet

Floor Bracket

to Install

RH Holes

Rear RH

Corner of

Cabinet Wall

NOTE:

If you did not receive an anti-tip bracket with your

purchase, call 1.800.626.8774 to receive one at no

cost. (In Canada, call 1.800.561.3344.)

For installation instructions of the bracket, visit: www.

GEAppliances.com.

(In Canada, www.GEAppliances.ca.)

Installation

Anti-Tip Floor Bracket

Instructions

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, and PWE) are

top heavy, especially with any doors open. These

models must be secured with the anti-tip floor

bracket to prevent tipping forward, which could result

in death or serious injury. Read and follow the entire

installation instructions for installing the anti-tip floor

bracket packed with your refrigerator.

PYE, PWE Models Only

Refer to 239D1142P001, Pub No. 31-45484-2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric PFE29 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info