Bedienungsanleitung General Electric PFE29 (Seite 35 von 47) (Englisch)

503105

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Installation Instructions

INSTALLING THE WATER LINE (cont.)

NOTE: The only GE approved plastic tubing

is that supplied in GE SmartConnect

™

Refrigerator

Tubing kits. Do not use any other plastic water

supply line because the line is under pressure at all

times. Certain types of plastic will crack or rupture

with age and cause water damage to your home.

$*(ZDWHUVXSSO\NLW FRQWDLQLQJWXELQJ

shutoff valve and fittings listed below) is available

at extra cost from your dealer or from Parts

and Accessories, 800.626.2002 (in Canada

1.800.661.1616).

$FROGZDWHUVXSSO\7KHZDWHUSUHVVXUHPXVWEH

between 20 and 120 p.s.i. (1.4–8.1 bar).

3RZHUGULOO

1/2” or adjustable wrench.

6WUDLJKWDQG3KLOOLSVEODGHVFUHZGULYHU

7ZR” outer diameter compression nuts

DQGIHUUXOHVVOHHYHV³WRFRQQHFWWKHFRSSHU

tubing to the shutoff valve and the refrigerator

water valve.

,I\RXDUHXVLQJD*(6PDUW&RQQHFW

™

Refrigerator Tubing kit, the necessary fittings

are preassembled to the tubing.

,I\RXUH[LVWLQJFRSSHUZDWHUOLQHKDVDIODUHG

fitting at the end, you will need an adapter

(available at plumbing supply stores) to connect

the water line to the refrigerator OR you can cut

off the flared fitting with a tube cutter and then

use a compression fitting. Do not cut formed end

from GE SmartConnect

™

Refrigerator tubing.

6KXWRIIYDOYHWRFRQQHFWWRWKHFROGZDWHUOLQH

The shutoff valve should have a water inlet with

a minimum inside diameter of 5/32” at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply

kits. Before purchasing, make sure a saddle-type

valve complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear

the line of water.

Install the shutoff valve on the nearest frequently

used drinking water line.

Choose a location for the valve that is easily

accessible. It is best to connect into the side

of a vertical water pipe. When it is necessary

to connect into a horizontal water pipe, make

the connection to the top or side, rather than at

the bottom, to avoid drawing off any sediment

from the water pipe.

CHOOSE THE VALVE LOCATION

DRILL THE HOLE FOR THE VALVE

Drill a 1/4” hole in the water pipe (even if using

a self-piercing valve), using a sharp bit. Remove

any burrs resulting from drilling the hole in

the pipe.

Take care not to allow water to drain into

the drill.

Failure to drill a 1/4” hole may result in reduced

ice production or smaller cubes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

General Electric PFE29 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info