Bedienungsanleitung Gezelschapsspellen Dungeons and Dragons Assault of the Giants (Seite 16 von 24) (Englisch)

700625

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

The possible combat dice results include the following:

• Each hit result that is not blocked inicts 1 damage.

There can be up to 4 hits on a single die face.

• Each miss result inicts no damage.

• Each block result cancels out one of the opponent’s

hit results. There can be up to 2 blocks on a single

die face.

• Each arcane result has the potential to be converted

into a dierent result through the use of Command

Cards or Spell Cards. Any arcane result that is not

converted or re-rolled is treated as a miss. There can

be up to 2 arcane results on a single die face.

After rolling the combat dice, the attacker may modify

the dice using any re-roll or conversion abilities that are

present on their face up Command Cards:

1) For each Command Card to the

right

of the Leader

Command, the attacker may re-roll 1 of their

combat dice.

2) For each Command Card to the

right

of the Magic

Command, the attacker may convert 1 arcane

result into 1 block result.

3) For each Command Card to the

left

of the Attack

Command, the attacker may convert 1 arcane

result into 2 hit results.

Each of these Command Card abilities may be initiated

once per combat, and all dice that are being re-rolled or

converted by a particular Command must be done at the

same time. To keep track of which Command Card abilities

have been used during a particular battle, the attacker

should shift those Command Cards down slightly as a

reminder that those abilities cannot be used again. When

converting a die to a particular result, the attacker should

physically turn the die face up to its new result to avoid

accidentally converting the same die result to two dierent

die results.

After using Command Cards, the attacker can further

modify their dice results through the use of Spell Cards or

Resource Cards that specify that they are activated during

a battle “before determining your nal totals.”

Once the nal hit total and block total have been

determined, the attacker should pick up the two red

combat tokens that are kept beside the game board and

use them to mark the results on the Combat Table on the

lower left part of the board.

BATTLES

When you play the Attack Command, your giants may

attack an adjacent enemy region. You cannot attack an

enemy’s Starting Region until the Final Ordning has begun

(see page 20). To resolve a battle, perform the following

steps in order.

1. Declare Attack

The attacker announces which friendly region they are

attacking from, and which enemy region they are invading.

The attacker can only initiate an attack from a single region

to an adjacent enemy region. The attacker also species

which of their giants are participating in the attack. Most

of the time, this will be all of the attacker’s giants in the

region, but sometimes the attacker may wish to exclude

certain giants so that they cannot be taken as casualties

or to limit the number of giants that will be forced to enter

the enemy region if it is conquered. Conversely, all of the

defender’s units must participate in the battle.

Important: The attacker does not actually move

their giants into the region unless they successfully

conquer it.

2. Cast “Start of Battle” Spells

Some spells specify that they are cast “at the start of a

battle.” First the attacker announces whether or not they

are casting any spells, and then the defender, and so on

back and forth until both players pass consecutively. If the

attacker passes but the defender casts a spell, the attacker

may still choose to cast a spell afterwards.

3. Attacker Determines Combat Totals

The attacker totals the Strength Values of all of their units

in the battle. Remember that a Champion Figure’s Strength

Value is listed on its corresponding Champion Card. The

total Strength Value of the attacker’s units determines

the number of combat dice that the attacker will roll, to

a maximum of 7 dice. The attacker always includes the

special combat die that is associated with their race as one

of their combat dice. The other dice rolled are the standard

combat dice.

For example, the re giants are attacking an enemy

region with 1 regular unit and 1 elite unit. The units’

total Strength Value is 2 + 2 = 4. The re giant player

rolls 4 combat dice (1 re combat die + 3 standard

combat dice).

Hit Miss Block Arcane

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gezelschapsspellen Dungeons and Dragons Assault of the Giants Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info