Bedienungsanleitung Gigaset E630 A GO (Seite 115 von 137) (Englisch)

647790

115

Zoom out

Zoom in

Vorherige Seite

1/137

Nächste Seite

113

Gigaset E630A GO / LUG_GO AU en / A31008-M2725-C401-1-7619 / appendix_legal_GO.fm / 11/8/17

Template Go, Version 1, 01.07.2014 / ModuleVersion 1.0

Customer service & product warranty – Australia and New Zealand

Operation behind routers with network address translation

(NAT)

In general, no special telephone or router configuration is required when operating a Gigaset telephone with

NAT router. The configuration settings described in this section are only necessary if you encounter one of the

following problems.

• No incoming calls are possible via VoIP. Calls to your VoIP phone numbers are not put through.

• Outgoing calls via VoIP are not connected.

• A connection is established with the other participant, but you cannot hear them and/or they cannot hear

you.

Changing the port numbers for SIP and RTP on your VoIP phone

¥ Connect to the telephone's web configurator using the PC web browser Register Open website Set-

tings – Telephony – Advanced VoIP Settings Change SIP and RTP port numbers Save settings

Example: Select port numbers that are similar to the standard settings:

¥ Check new settings: Open website Settings – Telephony – Connections . . . the Status of the VoIP set-

tings is displayed

¥ Test to see whether the original problem persists. If the problem does persist, carry out the next step.

Setting port forwarding on the router

Details for enabling a port on the router (example):

To enable the router to perform this port forwarding, the DHCP settings of the router must ensure that the

phone is always assigned the same local IP address.

Answer machine ( p. 43)

No time is specified for a message in the call list.

• Date/time are not set. Set the date/time ( p. 86)

The answer machine reports "Invalid PIN" during remote operation.

• You have entered the wrong system PIN. Repeat input of system PIN

• The system PIN is still set to 0000. Set the system PIN to something other than 0000 ( p. 89)

The answer machine is not recording any messages/has switched to answer only mode.

• The memory is full. Delete old messages Listen to new messages and then delete

The SIP and RTP port numbers may not be used by any other application or by any other host in the

LAN and should be completely different to the SIP and port numbers that are usually used (and pre-

set in the phone).

SIP port 49060 instead of 5060

RTP port 49004 to 49010 instead of 5004 to 5010

Protocol Public port Local port Local host (IP)

for SIP UDP 49060 49060 192.168.2.10

for RTP UDP 49004 – 49010 49004 – 49010 192.168.2.10

Protocol The protocol used must be UDP.

Public port Port number/port number range on the WAN interface

Local port The SIP and RTP port numbers set on the phone

Local host (IP) Local IP address of your phone in the LAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gigaset E630 A GO Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gigaset E630 A GO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info