Bedienungsanleitung Globe Fire Billy Elegance (Seite 14 von 16) (Englisch)

814084

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

22.

Alarm warnings:

In the event of a technical failure the circuit board will react and give warning of

the failure by switching on the LED alarm (LED alarm – on) and a warning sound

will be heard. The following alarms can be activated:

Each alarm will ensure that the stove is switched off immediately. WITH

THE EXCEPTANCE OF THE ALARM INDICATING A POWER CUT, the alarm

alert is activated at the end of a certain length of time and can be reset by

continually pressing the P3 button. Every time an alarm is reset the

switching off stage of the stove will restart for safety precautions. During

the alarm alert the alarm LED (Alarm LED on) is always on and the buzzer

(alarm sound) will sound intermittently when activated. If the alarm is not

reset the stove will be switched off and the alarm alert is always shown.

AL 1 – POWER CUT

A power cut can occur while the stove is on. If the cut is less than 20 seconds the

stove will switch back to the users mode. When this is activated and the power

cut is longer than 20 seconds the alarm is activated. 'AL 1 POWER CUT 'will

appear in the display and the stove is switched off.

Al 2 – AIR SENSOR (safety temperature thermostat)

This alarm is activated if the safety temperature thermostat is defect. The stove

switches to the alarm mode and the alarm – LED is activated. (Alarm-LED on).

The display will show “Al 2 air sensor and the stove is switched off.

AL 3 – FLUE GAS TEMPERATURE SENSOR (flue gas overheating)

This alarm is activated when the safety temperature thermostat detects that a

fixed temperature which cannot be changed has been exceeded. 'AL flue gas

temperature sensor 'appears in the display and the stove is switched off.

23.

AL 4 – SMOKE EXTRACTOR FAN

This alarm will be activated when the extractor fan is defect. The alarm will go off

and the signal “AL 4 smoke extractor fan” will appear in the display.

AL 5 – NO FLAME (no ignition):

This alarm will be activated when the ignition fails. This happens when the

temperature of the flue gas does not exceed the programmed temperature after

the set time. “Al 5 no flame “will appear in the display and the stove switches to

the alarm mode.

AL 6 – NO PELLETS

This alarm is activated when the flue gas temperature drops below the minimum

set temperature during the use of the stove .The signal 'AL 6 – no pellets' will

appear in the display and the alarm will be set off.

AL 7 – TEMPERATURE SAFETY

(Safety thermostat for too high a temperature):

This happens when the safely thermostat registers a temperature which is higher

than the limit. The thermostat reacts and switches off the auger. The display

shows the alarm is on (LED –alarm on) by the ´AL 7 temperature safety´ sign

and the stove is switched off.

AL 8 – PRESSURE ERROR (no vacuum / chimney draught)

This occurs when the pressure gauge detects pressure which is higher than the

limited pressure. The pressure gauge reacts and switches the auger off. The

alarm (LED alarm) is indicated by 'AL8 pressure error' in the display and the

stove is switched off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Globe Fire Billy Elegance Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Globe Fire Billy Elegance

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info