Bedienungsanleitung Godox Smart 120SDi (Seite 5 von 5) (Englisch)

656064

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Slave Trigger Model

This model offers three choices which can be set by the optical control and

anti-preflash switch (5).

1. No optical control: the slave trigger indicator (10) is off, meaning that the

slavetrigger model is shut down.

2. One fire model: the slave trigger indicator (10) glows blue, meaning the flash

will fire synchronously on one external flash. This model can act as an auxiliary

lamp, varying the light effects.

3. Anti-preflash model: the slave trigger indicator (10) glows red, meaning the

flash will fire synchronously on the second flash. This model can act as an

auxiliary lamp, applicable to TTL system. And with anti-preflash function, it can

work for the cameras equipped with one fire anti-preflash system.

Modeling Lamp

Modeling lamp switch (6) decides whether the modeling lamp is on or off: modeling lamp

indicator (11) on, modeling lamp is turned on;

the indicator (11) off, modeling lamp is turned off.

The lamp can also turn off automatically for auto-self protection after lighting for 30 minutes.

Brightness of the lamp can be adjusted by Flash Output Controller (4).

Buzz Function

Buzz function can be set by the buzz button (7) and it is turned on when the

buzz indicator (12) is on; it is shut off when the buzz indicator (12) is off. A “BI”

sound will be heard whenit is fully charged and ready to fire.

Model

Flash Output

Guide Number (m ISO 100)

Color Temperature

Power Voltage

Flash Power Control

Modeling Lamp

Recharging Time

Flash Triggering Method

Flash Duration

Fuse

Dimension

Weight

120SDI 160SDI 250SDI 300SDI

120WS 160WS 250WS 300WS

38 43 48 58

5600±200K

220V/50Hz or 100V~120V/60Hz

8 steps

75W

0.5~2sec

Sync cord, Test button, Slave

1/2000-1/800s

230*200*108MM

Approx.1.16KG

Shut down the device immediately when it works abnormally and find out the

reason.

Do not keep long time in using the modeling lamp. It's better to be

cooled down for one minute after five minutes continuous use.

Technical Data

Maintenance

07 08

Avoid sudden impacts and the lamp should be dedusted usually.

It's normal for lamp being warm when in use. Avoid continuous flashes when it

is not necessary.

Except that users can replace the plug-in tube and modeling lamp by themselves,

maintenance of all the flashes is up to our authorized maintenance department

which can provide original accessories.

One year warranty period will be canceled when any unauthorized maintenance is

found.

Disconnect the power when doing maintenance work or cleaning.

New changes made to the specification may not be updated in this manual.

If the product had failures or is wetted, it can be continuously used only after it

is repaired by professionals.

Tube Replacement

Turn down the power before replacing the flash tube and wear insulated gloves.

Then, loosen the iron wire on the tube, keep a balanced hold on the two feet of the

flash tube and pull out the old tube gently. Take down the feet casing to put it on

the new one. Hold two feet of the new tube, and target directly towards the two

copper outlets, then push them slightly in. Tighten the iron wire to fix the flash tube.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox Smart 120SDi Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info