Bedienungsanleitung Godox TT680 N (Seite 6 von 9) (Englisch)

656038

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

M: Manual Flash

The flash output is adjustable from 1/1 full power to 1/128th power in

1/3rd step increments.

Use a hand-held flash meter to determine the required flash output

to obtain a correct flash exposure.

0.5 0.7

1.5

6 9

1.7

2.3

10 15 20

40 60

Zoom

mm F

1. Press the <MODE> button

so that the <M> is displayed.

2. Set the flash output.

• Press the <SET> button.

• The flash output blinks.

• Press the < - > button to set a

lower value. Or press the <+>

button to set a higher value.

• Press the <SET> button again

to lock the settings.

• Press the shutter button

halfway to see the effective

flash range displayed.

128

Multi: Stroboscopic Flash

With stroboscopic flash, a rapid series of flashes is fired. It can be

used to capture multiple images of a moving subject in a single

photograph.

You can set the firing frequency (number of flashes per sec.

expressed as Hz), the number of flashes, and the flash output.

0.5 0.7

1.5

6 9

1.7

2.3

10 15 20

40 60

Zoom

1. Press the <MODE> button

so that <Multi> is displayed.

2. Select the item to be set.

• Press the <SET> button to

select the item (blinks).

Multi

Calculating the Shutter Speed

During stroboscopic flash, the shutter remains open until the firing

stops. Use the formula below to calculate the shutter speed and set

it with the camera.

Number of flashes / Firing frequency = Shutter speed

For example, if the number of flashes is 10 and the firing frequency

is 5 Hz, the shutter speed should be at least 2 sec.

To avoid overheating and deteriorating the flash head, do not use

stroboscopic flash more than 10 times in succession. After 10

times, allow the camera flash to rest for at least 15 min. If you try

to use the stroboscopic flash mode more than 10 times in

succession, the firing might stop automatically to protect the flash

head. If this happens, allow the camera flash to rest for at least

15 min.

• Stroboscopic flash is most effective with a highly reflective

subject against a dark background.

• Using a tripod, a remote switch, and external power source is

recommended.

• A flash output of 1/1 or 1/2 cannot be set for stroboscopic flash.

• Stroboscopic flash can be used with "buLb".

10 10

3. Set the desired number.

• Press the <-> button to set a

lower value. Or press the

<+> button to set a higher

value. Then press the <SET>

button. The next item to be

set starts blinking.

• After you set the flash output

and press the <SET> button,

all the settings will be

displayed.

0.5 0.7

1.5

6 9

1.7

2.3

10 15 20

40 60

Zoom

128

Multi

Range of flash output:

1/4<->1/8<->1/16<->1/32<->1/64<->1/128

Flash Output

When you change the flash output during shooting, the following

table will make it easier to see how the stop changes such as 1/2-

0.3→1/2+0.3 when you increase or decrease the flash output.

For example, when you decrease the flash output to 1/2, 1/2-0.3,

or 1/2-0.7, and then increase the flash output to more than 1/2,

1/2+0.3, 1/2+0.7, and 1/1 will be displayed.

1/1

1/1–0.3

1/2+0.7

1/1-0.7

1/2+0.3

1/2-0.3

1/4+0.7

1/2-0.7

1/4+0.3

1/2 1/4

...

Figures displayed when reducing flash output level→

←Figures displayed when increasing flash output level

• If you set the flash coverage manually, make sure it covers the

lens focal length so that the picture will not have a dark

periphery.

• If you use a commercially-available sync cord to connect the

camera to the camera flash' PC terminal, set the flash zoom

manually.

Using the Wide Panel

Pull out the wide panel and place

it over the flash head as shown.

The flash coverage will then be

extended to 14 mm.

• The catchlight panel will come

out at the same time. Push the

catchlight panel back in.

• The <ZOOM> button will not

work.

• If you use bounce flash with the wide panel in place, the subject

will be illuminated by both the bounce flash and direct flash,

which will look unnatural.

• Pull out the wide panel gently. Using excessive force may

detach the wide panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox TT680 N Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info