Bedienungsanleitung Godox V860IIN (Seite 11 von 14) (Englisch)

656032

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

● To avoid overheating and deteriorating the flash head, do

not fire the modeling flash for more than 10 consecutive

times. If you fire the modeling flash 10 consecutive times,

allow at least 10 minutes’ break for the camera flash.

Auto Focus Assist Beam

In poorly-lit or low-contrast shooting environments, the built-in auto

focus assist beam will automatically light on to make it easier for

autofocus. The beam will light up only when autofocus is difficult

and get out as soon as the autofocus becomes correct.

If you want to turn off the auto focus assist beam, set the “AF” to

“OFF” on the C.Fn settings.

● If you find the auto focus assist beam does not light up, this

is because the camera has got a correct autofocus.

Position

Center

Periphery

Effective Range

0.6~10m / 2.0~32.8 feet

0.6~5m / 2.0~16.4 feet

Bounce Flash

By pointing the flash head toward a wall or ceiling, the flash will

bounce off the surface before illuminating the subject. This can

soften shadows behind the subject for a more natural-looking shot.

This is called bounce flash.

To set the bounce direction, hold the flash head and turn it to a

satisfying angle.

360

-7-90

- 45 - - 46 -

Modeling Flash

If the camera has a depth-of-field preview button, pressing it will fire

the flash continuously for 1 second. This is called modeling flash.

It enables you to see the shadow effects on the subject and the

lighting balance. You can fire the modeling flash during wireless or

normal flash shooting.

Wireless shooting using radio transmission has advantages over

wireless shooting using optic transmission, such as being less affected

by obstacles, and not having to point the slave unit’s wireless sensor

toward the master unit. The main functional differences are as follows:

Function

Distance

Channel

To be disturbed

Radio Transmission

100m

1~32

Hard

Optic Transmission

15m

1~4

Easy

● Auto Shooting with Three Slave Groups

Other Applications

Wireless Control Function

The flash unit is built in with a Wireless Control Port so that you can

wirelessly adjust the power level of the flash and the flash triggering.

To control the flash wirelessly, you need a FT-16S

remote control set (on-camera and on-flash).

Insert its receive end into the Wireless Control

Port on the flash and insert the transmit end into

the camera hot shoe. Settings made on the

hotshoe-mounted transmit and receive ends

will be wirelessly communicated

to the flash. Then you can

press the camera shutter

release button to trigger

the flash. You can also hold

the transmit end at hand to

control your off-camera flash.

For full instructions on the use of FT series remote control, see its user

manual.

Sync Triggering

The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here

and the flash will be fired synchronously with the camera shutter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox V860IIN Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info