Bedienungsanleitung Godox X1N (Seite 8 von 14) (Englisch)

656020

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Setting the Transmitter

Multi Flash Parameter Setting

1. Enter into multi flash mode before setting.

2. Long press the <MODE> Button to enter multi flash

parameter setting menu.

3. Then, (output value), T (flash times) and H (flash

frequency) will be displayed on the LCD panel.

4. Short press the <GR> Button to choose the

settings. Turn the Select Dial to change the blinking

setting amount. Continue to press the <GR> Button

until all the amounts are set. Then, short press the

<MODE> Button to exit.

As flash times are restricted by flash output value and flash frequency, it might get automatic

adjustment. The times that transported to the receiver end are a real flash time, which is also

related to the camera’s shutter setting.

X1T-N transmitter + camera flash or X1R-N receiver + camera flash uses multi flash function can

only have one flash, which is determined by Nikon Communication Protocol. However, TT685N and

AD360II can be triggered normally when working as receivers.

Setting the Transmitter

Group Settings

Test Flash

1. Press the <TEST> Trigger Button to see the whether flash

will fire normally or not.

2. Fully press the <TEST> Trigger Button, and the Status

Indicator Lamp turns red and the flash on the receive end

can be triggered.

3. Use the transmitter to control camera to focus or shoot,

and the transmitter is connecting to the camera (do not

connect to the flash) now.

4. In the standby mode, press the TEST Button can wake up

the receiver.

5. The settings on the transmitter end will synchronize to the

receiver end at the same time.

Multi Flash Group ON/OFF Settings

1. Open the multi flash in the C.Fn Custom Functions

(set C.Fn-04 as on).

2. Short press <MODE> button to change the mode

of selected group.

3. The current group’s mode will be changed

simultaneously by the order of on/-- (-- represents

OFF, which means that the current group will not

fire flashes in this mode).

- 36 -- 35 -

1. Long press the <GR> Button to set all effective groups simultaneously.

2. The settings of all effective groups will blink. Turn the Select Dial to change the

settings, until one of the group's setting turns to the maximum or the minimum and all

settings of the effective groups will not change now.

3. If the current group is in the M mode, the power output value is changeable from 1/1

full power to Min. power in 0.3 stop increments, until one of the group’s setting turns to

the maximum(1/1) or the minimum(Min.). If the current group is in the TTL mode, all

the other groups which are in the M mode will change their FEC amount

simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop increments,

until one of the group’s setting turns to the maximum(3) or the minimum(-3). If the

current group is in the -- mode (flash off), the amounts will not change.

4. If the groups in the M mode or TTL mode work together, the first FEC amount which

up to the maximum or the minimum is considered as the limitation.

5. Short press the <GR> Button again to confirm the setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox X1N Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info