Bedienungsanleitung GoldenMask 5 (Seite 7 von 12) (Englisch)

654675

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Golden Mask 5 User Guide

GMD - www.goldenmaskdetectors.com - Golden Mask Ocial Reseller

Golden Mask 5 User Guide

GMD - www.goldenmaskdetectors.com - Golden Mask Ocial Reseller

3. All Metal (All)

Remember what we said about discrimination, in general? In All metal mode the discrimi-

nation is completely omitted and the detector is equally sensible to all type of metals.

You hear the response from all the metals with a single tone. The tone frequency can be

changed the same way you do it for the bitonal mode.

Identication of the target detected is possible by looking the Spectrum VDI graphic on

the LCD screen.

In All metal mode the Golden Mask 5 achieves the best depth of detection, but the dier-

ence with the Mono mode is not as big as you’d think. However there is a dierence and

this tiny dierence may be the depth you just need to detect an object. Unfortunately,

this mode is not comfortable in iron-polluted areas, but works best on places where a few

targets are present and you want to search at the maximum depth possible.

Setting the discrimination level (DL)

As it was said in the previous chapter, Golden Mask 5 does not have the usual discrimina-

tion setting other models have - you cannot control where to place the border between

the iron and the other metals, it is xed (or not exactly, as you will see bellow). And this is

done for two reasons:

1. To protect you making mistakes - setting a wrong discrimination border leads to many

good targets loss.

1. To ensure correct VDI for both 8 and 18kHz - with the frequency change, the response

from the target also changes. Moreover, the signal response changes also with the change

of the ground balance. To maintain an independent VDI display, that will show always the

same no matter what the working frequency and the ground conditions are, the discrimi-

nation border is xed, but only for the user. In fact it changes upon the detector settings

to ensure iron is always shown as iron, copper is always shown as copper and so on.

The Discrimination level (DL) setting is something dierent from the usual discrimination.

This setting (on the Golden Mask 5) controls how the detector handles iron targets. To

ensure a proper target identication, especially on big and/or deep targets, the detector

needs time. The faster the detector, the worse the target identication, and vice versa.

If you set a lower DL value, the detectors “holds” the signal for more time, so the signal is

properly identied by the processing engine. Lower values are good to properly identify

deep targets.

If you set a higher value of the DL, the signals are purged faster from the processor queue

and the detector becomes faster. But with faster signal processing, large iron objects

could be idetied as non-ferrous.

In brief: for deep search on clean areas, set the DL to a lower value; for trash-polluted areas

set the DL to a higher value.

Ground balancing (GB)

The ground balance is a setting that compensates for dierent ground conditions. There

are soils with no to very strong magnetic properties (the so-called mineralization), and the

detector needs to be tuned-up for the soil conditions on the area you are searching in.

There are also conductive soils (salt soils or wet beach sands) that also need ground

compensation. There is also a combination of both mineralization and conductivity, which

is the worse case - on such ground most detectors cannot be ground-balanced or are run-

ning with strongly reduced performance. The Golden mask 5 is no exception.

Strong mineralization reduces the working depth of the detector, while on low mineral-

ized soils the detector achieves its best working parameters.

Ground balancing depend also on the coil used. Usually, larger coils are harder to ground

balance.

The Golden Mask 5 has two options for ground balancing: Auto and Manual.

As you can guess, Auto ground balance is made automatically. It’s easy to be done, but it

is not always the best. Golden Mask 5 has a separate processor unit to perform the ground

balance in the best possible way. And it does it quite well, especially on light soils and lack

of electromagnetic elds.

Manual ground balancing the machine is best, if you perform it the right way. On tough

soils manual ground balance could dramatically increase the machine performance.

If you have troubles with the ground balance of your GM5, you should rst change the fre-

quency. This almost always solves the problem. If not, decrease the power level (PL) until

you are able to successfully ground balance your machine.

Remember: the ground balance is essential for the performance of every metal detector!

GROUND

BALANCE

AUTO

MANUAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

GoldenMask 5 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von GoldenMask 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info