Bedienungsanleitung Golmar Stadio Plus T500EN (Seite 13 von 18) (Englisch)

655051

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

TELEPHONES PROGRAMMING

rogramming the

telephones.

Set to ON the switch number 2 of the configuration dip switch, that's

accessible by opening the terminal connector protection cover.

The door panel will reproduce a sound to advise that the system

has entered into programming mode.

In systems with more than one door panel, the programming process

shall be done on the master door panel only.

Switch off the telephone to be programmed.

Once the telephone is off, press the door release push button.

With the door release push button pressed

switch on the telephone.

To show that the system is ready for programming,

the door panel will reproduce a sound and

the telephone led will blink. At this moment, the door

release push button can be released. Lift the handset

to establish audio communication with the door panel.

Press the door panel push button that will

call to this telephone. At this moment

the door panel will reproduce a sound

and the telephone led will blink.

To program the telephone as master,

switch it off and on again.

To program it as slave, press the door

release push button.

To program it as slave with intercom

function press the center push button.

Each apartment must have one master unit only; in case of parallel units configure them

as slaves, both monitors or telephones.

Make a call to check that the telephone has been succesfully programmed.

Repeat these steps to program the rest of telephones.

Once the programming has been finished, set to OFF the programming

switch. If you don't, the door panel will reproduce a sound to advise

that the system is still into programming mode.

MRBO T

R-3

TF-104

SEC

CV+CV- D

Malla

Vin-AinAout Vin+ Vout-Vout++

CN1

INSTALLATION DIAGRAMS

onnexion of an a.c. lock release.

As it is described on page 14, the lock releases to be connected to the door panel

must be d.c. type. If an a.c. lock release has been installed before, use a R-3

relay unit and a TF-104 transformer, and connect them to the lock release

as it is shown on the enclosed diagram.

ink of several power supplies units.

If the quantity of monitors or telephones to be connected is bigger than the supported

from one power supply (see page 14), use additional power supplies to match the

required quantity. The first power supply should be connected to the door panel and

to the first group of monitors or telephones; connect the next groups to the positive

terminal of its corresponding power supply.

To wire several power supplies link their ground terminals;

NEVER link positive terminals of different power supplies.

To the door panel and to

the first group of monitors

or telephones.

To the second group of

monitors or telephones.

1st FA-Plus 2nd FA-Plus/C or FA-Plus

SEC

PRI

Main

+ +

SEC

PRI

Main

+ +

Door panel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Golmar Stadio Plus T500EN Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info