484818
22
Zoom out
Zoom in
Vorherige Seite
1/47
Nächste Seite
PRO TIPS: ATTACHING ADHESIVE MOUNTS
Clean the surface first. Be sure to carefully clean the surface where you will
be attaching your adhesive mount. Wax, oil, dirt and other debris will reduce
adhesion, which can result in a weak bond and the risk of losing your camera
if the bond fails.
Only attach a mount in room temperature conditions. The mount’s adhesive
will not bond properly if applied in cold or damp environments, though it is
entirely safe to use in cold conditions. For best results, attach your mount 24
hours before use in cold environments to ensure the strongest hold.
Surfaces. The adhesive mounts can only be mounted to a smooth surface.
Porous or textured surfaces will not provide for a proper bond. When
applying the mount, firmly press mount into place ensuring full contact over
entire surface area. Allow at least 24 hours for full bond strength.
Drying time. For best results, attach your mount at a minimum of 24 hrs
before use.
LOCKING PLUG
This locking plug is designed for high impact sports like surfing
or skiing where significant impact can occur. The locking plug
locks the attachment buckle’s fingers in place, helping to prevent
accidental housing release from mounts.
CAMERA ASSEMBLY FCC STATEMENT
Modifications not approved by the party responsible for compliance could void
user’s authority to operate the equipment. This equipment has been tested and
found to comply with the limits for Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which
can be determined by turning the equipment on and off
.
The user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
42 43
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für GoPro HD Hero 2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von GoPro HD Hero 2

GoPro HD Hero 2 Bedienungsanleitung - Deutsch - 45 seiten

GoPro HD Hero 2 Bedienungsanleitung - Französisch - 45 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info