Bedienungsanleitung Gorenje DCM700 O (Seite 17 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

603298

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

blanks with a screwdriver or other suitable tool, and ﬁx the air

outlet ﬂange with the screws as shown in Figure 1C.

If you install the unit in its suction version and place the engine

over the hood, remove the metal blank with a screwdriver or

other suitable tool, and tighten the engine group by using

the screws provided (Fig. 1B).

- Make the hole in the ceiling to accommodate the device

taking into account the dimensions shown in Figure 2.

ATTENTION: Make sure that the ceiling structure supports

the unit's weight. If not, prepare a suitable frame to fulﬁl

such function.

- Tighten the power box over the upper part of the hood using

the screws provided (Fig. 5).

- With a ﬁtting pipe, connect the ﬂange (Fig. 1C) to the air

extraction hole.

- Take the unit and place it inside the hole, just as you did in

the ceiling. Make sure that the brackets are perfectly hooked

(Fig. 6A).

- Tighten the brackets by using the screws inside the hood, as

shown in Figures 6B and 6C.

- If necessary, there is also the possibility of ﬁxing the device

with additional screws from inside the hood to an under-

counter light (if present) (Fig. 2A).

- For diﬀerent types of assemblies, use screws and anchors

that are suitable for the wall material (e.g.: reinforced concrete,

plasterboard, etc).

If the screws and anchors are provided with the product,

make sure that they are suitable for the type of wall to which

the hood is ﬁxed.

USE AND MAINTENANCE

•We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eﬀective performance of the cooker hood depends on

constant maintenance; the anti-grease ﬁlter and the active

carbon ﬁlter both require special attention.

•Theanti-greaselter is responsible retaining the grease

particles suspended in the air, therefore it is subject to

clogging with variable frequency according to the use of the

appliance.

- To prevent the danger of possible ﬁres, at least every 2

months one must wash the anti-grease ﬁlters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Beforeremountingtheanti-greaseltersandtherege-

nerable active charcoal ﬁlters it is important that they are

completely dry.

•Clean the hood frequently, both internally and externally,

using a cloth dampened with denatured alcohol or neutral

liquid detergents that are non abrasive.

•The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system signiﬁcantly decreases

the average duration of the bulbs.

•If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: The non compliance with the hood cleaning

warnings and with the replacement and cleaning of the ﬁlters

entails risk of ﬁres. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.9):

To replace the halogen lamps, B push the watch glass C and

open the ﬂap. Replace them with a light of the same type.

Attention: Do not touch the lights with your hands.

If the appliance version includes LED lamps, the intervention

of a specialised technician is necessary to replace them.

•Commands(Fig.10):

NOTE: All units’ functions are controlled through a remote

control.

If the remote control stops functioning (because of low

batteries, etc.) you can directly use the control inside the

unit (Fig. 8-10).

PowerButton(A)= The on/oﬀ button switches on and oﬀ

the whole hood (motor and lights).

By pressing the button the motor starts at 1st speed.

FanSpeedbutton(B)= From the OFF position, press once

for the 1st speed, twice for the 2nd speed and three times

for the 3rd speed. In order to activate the intensive speed,

press the button for 5 seconds regardless of the status of the

hood. For each speed only the led indicating the set speed

will turn on. The intensive speed is indicated by the ﬂashing

of the led indicating speed 3. The duration of the intensive

speed is 10 minutes; after this time the hood goes back to

the last set speed.

In order to remove the intensive speed press the power button

and the hood will switch oﬀ, or press the Fan speed button

and the speed goes back to the previously set one. Speed of

the hood with cyclic trend.

Lightbutton(C)= There are three light levels: High, me-

dium, low.

From the oﬀ position press once for the high level, twice for

the medium level, three times for the low level and four times

to turn the lights oﬀ.

The level of the lights has a cyclic trend: High, medium,

low, oﬀ.

Timerbutton(D)= With any type of speed (excluding the

intensive speed), by pressing the button, the timer function is

activated for 15 minutes. After this time has elapsed the hood

will turn oﬀ (motor and any light on).

Lightsindicator(E)= The lights indicator will switch on when

the lights are on at any level.

Filtersindicator(F)= After 30 minutes of operation, the led

of the ﬁlters indicator will switch on, not ﬂashing indicating

that the anti-grease ﬁlters have to be washed. To reset the

function (with the hood oﬀ), press the Fan speed button for

5 seconds. After this operation, the led of the ﬁlters indicator

turns oﬀ and the setting of the 30 hours starts again from

the beginning.

Clean air indicator (8).

With the hood oﬀ, press the Power button (1) for 5 seconds to

activate the clean air function. This will switch on the motor

at speed 1 for 10 minutes every hour. The light indicator will

switch on without ﬂashing and the led of the 1st speed will

switch on. In the remaining 50 minutes the light indicator will

ﬂash. The function can be deactivated by pressing any button

except for the lights one.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

- 17 -

Gorenje DCM700 O Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info