Bedienungsanleitung Gorenje DF6430 (Seite 16 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

603616

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

•ElectricConnection:

- The appliance has been manufactured as a class II, therefore

no earth cable is necessary. The plug must be easily accessible

after the installation of the appliance. If the appliance

is equipped with power cord without plug, a suitably

dimensioned omnipolar switch with 3 mm minimum opening

between contacts must be fitted between the appliance and

the electricity supply in compliance with the load and current

regulations.

- The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral.

•  The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm. If a connection

tube composed of two parts is used, the upper part must be

placed outside the lower part. Do not connect the cooker

hood exhaust to the same conductor used to circulate hot air

or for evacuating fumes from other appliances generated by

other than an electrical source. Before proceeding with the

assembly operations, remove the anti-grease filter(s) (Fig.4)

so that the unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•  We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with

a smaller diameter is used, the efficiency of the product may

be reduced and its operation may become noisier.

•  If your appliance has been designed for use in habitations

supplied with acentralised suction device perform the

following operations:

- The switch controls opening and closure of a valve using

a thermoelectical device. By placing the switch in the ON

position, after a minute, the valve opens rotating 90° allowing

suction of the stale air. By placing the switch in the OFF

position, the valve closes after 100 seconds.

•Installation:

The following instruction should be followed to carry out the

correct installation of the cooker hood.

1. Mounting of the cooker hood on the lower side of the

cupboard.

2. Selection of the version (extraction Fig.3A or filtration

Fig.3B).

•  Fixingthehoodtothelowerpartofthewallcabinet:

This type of appliance must be fitted inside a cabinet or

inside another type of support structure. To fix it in place, use

4 screws which are suitable for the type of cabinet, making

holes in accordance with the diagram shown in (Fig.1). To fit

the appliance correctly, align the front panel of the cooker

hood with the cabinet door and adjust spacer L using screws P

(Fig.2), then ensure the appliance meets the cabinet at the rear.

•Extractionthroughanoutsidewall:

The appliance expels the fumes through an outside wall or

a duct. It is necessary to buy a telescopic pipe in accordance

with the standards in use (inflammable) and connect it to

flange H (Fig.3A).

•Recirculation:

To transform the cooker hood from the extraction version to

the re circulating one ask your supplier for an activated carbon

filter. The filter must be fitted to the extracting group cooker

hood in the centre of the fan grille by twisting it by 90 degrees

until it is gripped securely (Fig.5). For this operation remove the

anti-grease filter(s) G (Fig.4). The clean air is returned into the

room through a connecting tube passing inside the cupboard

and connected to the ring H (Fig.3B).

USE AND MAINTENANCE

•  We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air. The effective

performance of the cooker hood depends on constant

maintenance; the anti-grease filter and the active carbon filter

both require special attention.

•Theanti-greasefilter is responsible retaining the grease

particles suspended in the air, therefore it is subject to

clogging with variable frequency according to the use of the

appliance.

- To prevent the danger of possible fires, at least every 2

months one must wash the anti-grease filters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Theactivecarbonfilters are used to purify the air that is

sent back into the room and its function is to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon filters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

•Beforeremountingtheanti-greasefiltersandthe

regenerable active charcoal filters it is important that they

are completely dry.

•Clean the hood frequently, both internally and

externally,usingaclothdampenedwith denatured

alcohol or neutral liquid detergents that are non abrasive.

•  The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system significantly decreases

the average duration of the bulbs.

•  If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: the non compliance with the hood cleaning

warnings and with the replacement and cleaning of the filters

entails risk of fires. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.6):

To replace the halogen light bulbs B, remove the glass pane C

using a lever action on the relevant cracks. Replace the bulbs

with new ones of the same type. Caution: do not touch the

light bulb with bare hands.

•Commandsslider(Fig.7)thekeysymbolsareexplained

below:

A = Light switch

A1 = Off key

A2 = On key

B = Speed control

B1 = Off key

B2 = FIRST SPEED key

B3 = SECOND SPEED key

B4 = THIRD SPEED key

- 16 -

Gorenje DF6430 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info