Bedienungsanleitung Gorenje DF9131E (Seite 19 von 40) (Alle Sprachen)

603308

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

- 19 -

which should be fitted before the hood is installed (Fig. 2a).

Fix the spacer to the hood using screws P (Fig. 2a).

To assemble the unit correctly, align the front panel of the

hood with the wall cabinet and decide on the distance

necessary to fill in any space remaining between the hood

and the wall.

Once the distance has been established, use a cutter to

remove the excess plastic (Fig. 2a).

• INSTALLATION

The following instruction should be followed to carry out

the correct installation of the cooker hood.

1) Mounting of the cooker hood on the lower side of

the cupboard.

2) Selection of the version (extraction or filtration)

• FIXING THE HOOD TO THE LOWER PART OF THE

WALL CABINET

This type of appliance must be fitted inside a cabinet or

inside another type of support structure. To fix it in place,

use 4 screws which are suitable for the type of cabinet,

making holes in accordance with the diagram shown in

(fig. 1). To fit the appliance correctly, align the front panel

of the cooker hood with the cabinet door and adjust

spacer E using screws P (fig. 2), then ensure the

appliance meets the cabinet at the rear.

• EXTRACTION THROUGH AN OUTSIDE WALL

The appliance expels the fumes through an outside wall

or a duct. It is necessary to buy a telescopic pipe in

accordance with the standards in use (inflammable) and

connect it to flange B (Fig 3).

• RECIRCULATION

To transform the cooker hood from the extraction version

to the re circulating one ask your supplier for an activated

carbon filter.

The filter must be fitted to the extracting group cooker

hood in the centre of the fan grille by twisting it by 90

degrees until it is gripped securely (Fig 6). For this

operation remove the anti-grease filter(s) G (Fig 5). The

clean air is returned into the room through a connecting

tube passing inside the cupboard and connected to the

ring B (fig 4).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on

before any food is cooked. We also recommend that the

appliance is left running for 15 minutes after the food is

cooked, in order to thoroughly eliminate all contaminated

air.

The effective performance of the cooker hood depends

on constant maintenance; the anti-grease filter and the

active carbon filter both require special attention.

• The anti-grease filter is used to trap any grease particles

suspended in the air, therefore is subject to saturation

(the time it takes for the filter to become saturated

depends on the way in which the appliance is used).

The acrylic filter, which is found resting on the grille,

should be replaced when the text, visible through the

grille, changes colour and the ink spreads; the new filter

should be fitted in such a way that the text can be seen

through the grille from outside the cooker hood.

If the filters do not have any text on them, or if metal

filters or aluminium panel filters are used, they should

be washed every 2 months in order to prevent the risk of

fire. To wash the filters, proceed as follows:

- Remove the filter from the grille and wash it using a

solution of water and neutral liquid detergent, leaving

the dirt to soften.

- Rinse thoroughly with warm water and leave to dry.

The metal filters and/or aluminium panel are also

dishwasher safe. If the filters are made using aluminium,

or if an aluminium panel is used, after a few washes the

colour may change. This does not mean they have to be

replaced.

If the replacement and washing instructions are not

followed, the anti-grease filters may present a fire hazard.

• The active carbon filters are used to purify the air which

is released back into the room. The filters are not

washable or re-usable and must be replaced at least once

every four months. The active carbon filter saturation level

depends on the frequency with which the appliance is

used, the type of cooking performed and the regularity

with which the anti-grease filters are cleaned.

• Remove build-up from the fan and other surfaces of

the cooker hood regularly using a cloth moistened with

denatured alcohol or non-abrasive neutral liquid

detergent.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination. Extended

use of the light reduces the average duration of the bulb.

• Replacing halogen light bulbs (Fig. 7).

To replace the halogen light bulbs B, remove the glass

pane C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•COMMANDS: (pic.8) SLIDER

the key symbols are ex-

plained below:

A = Light switch

A1 = Off key

A2 = On key

B = Speed control

B1 = Off key

B2 = FIRST SPEED key

B3 = SECOND SPEED key

B4 = THIRD SPEED key

THE MANUFACTURER DECLINES ALL

RESPONSIBILITY FOR EVENTUAL DAMAGES

CAUSED BY BREACHING THE ABOVE WARNINGS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje DF9131E Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info