Bedienungsanleitung Gorenje DK9330 (Seite 16 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

603634

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

- 16 -

•ElectricConnection:

Note! Verify the data label placed inside the appliance:

- If the symbol

appears on the plate, it means that no earth

connection must be made on the appliance, therefore follow

the instructions concerning insulation class II.

- If the symbol

DOES NOT appear on the plate, follow the

instructions concerning insulation class I.

Insulation class II

- The appliance has been manufactured as a class II, therefore

no earth cable is necessary.

The plug must be easily accessible after the installation of the

appliance. If the appliance is equipped with power cord with-

out plug, a suitably dimensioned omnipolar switch with 3 mm

minimum opening between contacts must be fitted between

the appliance and the electricity supply in compliance with the

load and current regulations.

- The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral.

Insulation class I

This is a class I, appliance and must therefore be connected to

an effiecient earthing system.

- The appliance must be connected to the electricity supply as

follows:

BROWN = L line

BLUE = N neutral

YELLOW/GREEN =

earth.

The neutral wire must be connected to the terminal with the

N symbol while the YELLOW/GREEN, wire must be connected

to the terminal by the earth symbol

When connecting the appliance to the electricity supply, make

sure that the mains socket has an earth connection. After fitting

the ducted cooker hood, make sure that the electrical plug is

in a position where it can be accessed easily. If the appliance

is connected directly to the electricity supply, an omnipolar

switch with a minimum contact opening of 3 mm must be

placed in between the two; its size must be suitable for the

load required and it must comply with current legislation.

•  The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm. If a connection tube

composed of two parts is used, the upper part must be pla-

ced outside the lower part. Do not connect the cooker hood

exhaust to the same conductor used to circulate hot air or for

evacuating fumes from other appliances generated by other

than an electrical source. Before proceeding with the assembly

operations, remove the anti-grease filter(s) (Fig.7) so that the

unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•  We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with a

smaller diameter is used, the efficiency of the product may be

reduced and its operation may become noisier.

•  If your appliance has been designed for use in habitations

supplied with acentralised suction device perform the fol-

lowing operations:

- The switch controls opening and closure of a valve using

a thermoelectical device. By placing the switch in the ON

position, after a minute, the valve opens rotating 90° allow-

ing suction of the stale air. By placing the switch in the OFF

position, the valve closes after 100 seconds.

•Fixingtothewall:

Make hole A respecting the shown dimensions (Fig.2). Fix de-

vice to wall and align it horizontally with the cupboards. When

the appliance has been adjusted, definitely fix the hood using

the screws A (Fig.5). For the various installations use screws

and screw anchors suited to the type of wall (e.g. reinforced

concrete, plasterboard, etc.). If the screws and screw anchors

are provided with the product, check that they are suitable for

the type of wall on which the hood is to be fixed.

•Fixingthedecorativetelescopicflue:

Arrange the electrical power supply within the dimensions of

the decorative flue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening. Install the upper decorative flue's sup-

port bracket and fix it on the wall using the screws A (Fig.3) so

it is in axis with your hood and respecting the distance from

the ceiling shown in Fig.2. Connect flange C to air extraction

hole via an air extraction pipe (Fig.5). Insert upper decorative

flue inside the lower decorative flue and rest them on top of

the frame. Extract the upper flue up to the bracket and fix it

with the screws B (Fig.3). To transform the hood from a ducting

version into a filtering version, ask your dealer for the charcoal

filters and follow the installation instructions.

•Filteringversion:

Install the hood and the two flues as described in the para-

graph for installation of the hood in ducting version. Connect

air diverter M to bracket and fix it with screws I as shown in

Fig.4. The active charcoal filters must be applied to the suction

unit inside the hood, centring them in it and turning them 90°

until they snap into place (Fig.8).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air. The effective

performance of the cooker hood depends on constant main-

tenance; the anti-grease filter and the active carbon filter both

require special attention.

•Theanti-greasefilter is responsible retaining the grease

particles suspended in the air, therefore it is subject to clogging

with variable frequency according to the use of the appliance.

- To prevent the danger of possible fires, at least every 2

months one must wash the anti-grease filters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Theactivecarbonfilters are used to purify the air that is

sent back into the room and its function is to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon filters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

•Beforeremountingtheanti-greasefiltersandtheregen-

erable active charcoal filters it is important that they are

completely dry.

•Cleanthehoodfrequently,bothinternallyandexternally,

using a cloth dampened with water or non-abrasive neutral

liquid detergents.

• The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

Gorenje DK9330 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info