Bedienungsanleitung Gorenje DQG8530 (Seite 22 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

603622

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

the cooker hood must be at least 48 cm. If a connection

tube composed of two parts is used, the upper part must be

placed outside the lower part. Do not connect the cooker

hood exhaust to the same conductor used to circulate hot air

or for evacuating fumes from other appliances generated by

other than an electrical source. Before proceeding with the

assembly operations, remove the anti-grease lter(s) (Fig.5B)

so that the unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•  We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with

a smaller diameter is used, the eciency of the product may

be reduced and its operation may become noisier.

•ATTENTION!Remove screws “F” (Fig. 2) before

plugging in the appliance. These screws fasten down

the counterweight, required for opening the front panel,

during transport of the appliance. The screws may be on

one or both sides of the hood, depending on the version.

A label, or possibly several, indicate the location of the

screws (Fig.2A).

•  There is a manual or electronic vent on the front of the

appliance for increasing the extraction capacity.

- If the vent on the front of the appliance is manual, pull the

panel outwards (Fig.3A).

- If the vent on the front of the appliance is electronic, press

button D for about four seconds (Fig.17).

•Wallmounting:

- Mark the lower part of the back of the hood on the wall, Fig.4A

(taking into account the minimum distance from the hob).

- Position the xing template on the wall, making sure that

the line coincides with the line previously made on the wall.

- Mark the fixing holes and cut them into the material

(Fig.4B).

- Fasten the 7 rawl bolts and the 2 screws C without tightening

them fully (Fig.4B).

- Position the appliance at the wall (Fig.6).

- Make sure the 2 levelling screws J are tightened (Fig.7).

- Align the appliance horizontally using the two levelling

screws J (Fig.7).

- When you have done the above, open panel K (Fig.5) and

remove the anti-grease lter (Fig.5B). It is now possible to

fasten the hood on denitively by tightening screws C and D

(Fig.6).

- For easy accessibility to the motor unit in the case of

assistance, after having levelled and fixed the appliance

denitively, we recommend that the brackets are removed

(Fig.7A).

- When carrying out the xing operations, use only screws

and screw anchors suited to the type of wall (e.g. reinforced

concrete, plasterboard etc.).

- If the screws and screw anchors are supplied with the

appliance, make sure that they are suited to the type of wall

to which the hood must be xed.

•Installationofmodelswithoutdecorativeducts:

Extractorhood

- Unclip the canopy M and remove the grille E (Fig.14A).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.14B.

- Taking the grommet H, position it between the power cable

and the slot.

- Warning: the cooker hood may be installed with the air

exhaustoutletattherear,byremovingbracketXwiththe

motor and rotating it, as illustrated in Fig.12.

The wall mounting bracket Y should also be removed and

xedasillustratedinFig.12,usingthesamescrews.

- Connect the exible hose L (not supplied) to the hood, so

that it is aligned with the air exhaust outlet.

If the air exhaust is on top, use Fig.13A as a guide; otherwise,

if it is at the rear, use Fig.13B as a guide.

- Fix the small cupola M and the grille E making sure that is it

perfectly hooked on to the fastening pins G (Fig.13B).

- Filtering version:

- Unclip the canopy M and remove the grille E (Fig.14A).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.14B.

- Taking the grommet H, position it between the power cable

and the slot.

- To insert the active carbon lters iin the hood, undo the

support G (Fig.5A). Open and lift panel K. Remove the anti-

grease lter by pulling the handle as shown in Fig.5B. Hold

the active carbon lters Z and t them in as shown in Fig.5C.

- Fix the small cupola M and the grille E making sure that is it

perfectly hooked on to the fastening pins G (Fig.13B).

•Installationofmodelswithdecorativeducts:

-Extractorhood

- The fairing M should be removed before installing decorative

ducts (Fig.14A).

- Make sure the electrical power supply is within the

measurements of the decorative connector.

- If your appliance is to be installed in the ducting version or

in the version with external motor, prepare the air exhaust

opening.

- Adjust the width of the support bracket of the top connector

(Fig.9).

- Next, fasten it onto the wall making sure it is perfectly aligned

with the hood, using the screws A (Fig.9). It must be at the

correct distance from the ceiling, as shown in Fig.8.

- Connect ange F to the air exhaust hole using exible hose

L (Fig.10).

- Slide the top connector inside the lower duct and place this

on the body (Fig.11).

- Pull out the top duct as far as the bracket and secure it using

screws B (Fig.11).

- Filter version:

Attention!

- If you wish to turn your EXTRACTOR hood into a FILTER

one, you need to contact your retailer to order either non-

regenerative active carbon lters (Fig.5C) or regenerative active

carbon lters (Fig.15). These are available as accessories.

•Onrequest:

- The version with manual front vent can be equipped, on

request, with an “ambient light”. This function is activated by

pressing button “D” (Fig.17) for about 4 seconds. To turn off

the light, simply press and hold the same button for about 4

seconds.

USE AND MAINTENANCE

•  We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

- 22 -

Gorenje DQG8530 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info