335435

Gorenje ect 600 e Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
Instructions for use, mounting and connection
25
Control elements
Once the glass ceramic hob is connected to the mains
(including the power failure), the appliance will perform the
process of initial synchronization with the exterior environment,
in order to provide the most efficient sensor function and
render the best control.
After the successful accommodation to the environment had
been completed, the indicators show the mark "-" for a
moment which eventually disappears.
The sound signal confirms the appliance is now ready for use.
Do not place any objects upon the sensor surface during the
accommodation period, otherwise you may provoke error
mode. In such cases the process is interrupted and all
indicators display the symbol ''F''. The hob fails to respond to
commands.
The hob is equipped with electronic sensors which are
switched on by touching or pressing the relevant sensor
surface with your fingertip.
Each sensor reaction is confirmed by the beep.
Be sure to always touch only one sensor at the time, and for a
very brief period of time (approximately 1 second). If more than
one sensor is pressed at the same time the relevant command
is not accepted. If the touch is prolonged it provokes error
mode and the appliance is switched off.
Do not place any objects upon the sensor surface (error mode)
nor any hot dishes which may damage the sensors. Keep the
sensor surface clean at all times.
Switching the hob on
When the hob is turned off all the hotplates are off and
indicator LED's are off.
To switch the hob on, touch the ON/OFF sensor. The hob is
activated and the hob #4 power display indicates flashing »0«
for a period of 10 seconds. Other hob indicators are not
illuminated. In case the main ON/OFF sensor was pressed for
more than 2 seconds, the hob is switched off and needs to be
restarted. Using the (+) or (-) sensor you may select the
desired cooking power in 10 seconds following the switch on or
selection of a particular hotplate.
Selecting the particular hotplate
Once the hob is switched on with the ON/OFF sensor, activate
the hotplate selection sensor to select the next hotplate in the
clockwise direction, always starting with hotplate #4. The
indicator flashes 10 seconds after the hotplate and its power
setting are selected. Active hotplate is indicated by flashing
power setting. By touching the (+) sensor you select setting "9"
and activate automated cooking mode. Current setting may be
reduced by touching the (-) sensor in short intervals. Prolonged
pressing speeds up the setting reduction. If you switch the
hotplate on by touching the (-) sensor, the power selection
indicates "4". This setting may then be increased or reduced by
pressing either (+) or (-) sensor and select the desired heating
power.
If the hotplate selection sensor is touched once again, you
select the next hotplate in clockwise direction, and this is
signaled by flashing of the indicator.
If only one hotplate is activated, by pressing the hotplate
selection sensor this hotplate is selected directly. In case more
than one hotplate is active, the first one to be activated is
always hotplate #4.
Switching the hotplate on
Once the hotplate is selected and its indicator flashes ''0'', you
have 10 seconds to select the desired power setting by
pressing either sensor (+) or (-). Indicator will flash the
selected setting, and after 10 second lapse this setting
becomes default.
If no power setting is selected within 10 seconds, the indicator
''0'' goes off and the hotplate is switched off.
Automatic cooking mode
When the automatic cooking mode is activated the hotplate will
operate at maximum power for a limited period of time
(depending upon the power level required for continuation) and
then automatically switch to the reduced power level to resume
cooking (see chart). It may be switched on in any of the
hotplates for all power settings except for maximum
setting 9.
Select the desired hotplate by touching the hotplate selection
sensor. Indicator ''0'' flashes.
Activate the automatic cooking mode by touching the (+)
sensor. In case setting "9" is not changed within the next ten
seconds the automatic cooking mode is off. It remains active if
you press the (-) sensor and reduce the power setting to any
value between 8 and 1. This means that the maximum setting
"9" must first be reduced by pressing the (-) sensor, and then it
may be increased by touching the (+) sensor. The indicator
displays letter ''A'' which remains illuminated for the entire time
the automatic cooking mode is on. Automatic cooking mode
will not function on power setting "9".
If you wish to check the power setting level of active hotplates
during automatic cooking mode, touch either (+) or (-) sensor.
The indicators of all active hotplates functioning in automatic
cooking mode will display the current power setting.
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

gorenje-ect-600-e

Suche zurücksetzen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gorenje ect 600 e wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info