Bedienungsanleitung Gorenje GKTG6SY2 (Seite 7 von 14) (Englisch)

603659

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

• When connecting, the knee R1/2 should be held firmly to prevent it from rotating.

• For sealing of the connection joints, use a non-metal approved gaskets and

approved sealants.

• The gaskets should only be used once. The thickness of the flat non-metal gaskets

should not be deformed more than by 25 percent.

• To connect the appliance to the gas supply, use a tested and certified flexible hose.

• The flexible connection hose should be able to move freely.

It should not come into contact with the movable parts of the furniture or the bottom

of the cooking hob.

• If an electric oven is built into the kitchen element under the cooking hob, it should

be fitted with a cooling fan.

After connecting the gas hob, check the joints for any leaks.

Gas supply connection plug

A ISO7-1 R1/2 connection plug

B Non-metal gasket with thickness of 2 mm

C Pipe adapter for liquid gas (depending on the model)

Only use pipes and seals in accordance with the Standards. These pipes must

be installed so that, when fully extended, their length does not exceed 2000 mm. For

easier installation and to prevent gas leaks, attach the swivel coupling to the cook

top first, and then to the gas mains pipe. Inverting this sequence may hamper the

gas seal between the pipe and the cook top.

Important: when the installation is complete, check that all couplings are

completely sealed by using a soapy solution. Never use a flame. Also ensure

that the flexible pipe cannot come into contact with any moving part of the

cook top (e.g. drawer) and that it is not in a position where it could be

damaged.

After the connection, check the burners for correct operation.

The flames must be clearly visible, and should be blue and green at the center. If the

flame is unstable, increase the minimum power.

Adaptation to a different

type of gas

• The procedure or adaptation of the cooker to another type of gas does not require

removal of the appliance from the worktop.

• Before adapting, disconnect the appliance from the power mains and close the gas

supply valve.

• Replace the existing nozzles for nominal thermal load with corresponding nozzles

for the new gas type and supplied provided (see table below).

• After finishing this sequence, replace the old setting label with the new one

provided for the new injectors.

Adjustment elements

To leave the adjustment elements accessible, please observe the following

instructions:

• Remove the support grid and burner covers with respective crowns.

• In double burners, adjustment elements are accessible behind the main nozzle

protective plate.

• Remove the control knobs, including the gaskets.

Gas valve

Minimum thermal load regulation valve

Minimum flow adjustment

Instructions for urban (G110, G120, G150.1) and methane gas (G20, G25)

1. Light the burner and bring it to the minimum position.

2. Remove the gas tap knob and turn the adjustment screw on the side of the tap

rod:

•

anti-clockwise to increase the gas flow

•

clockwise to reduce the gas flow

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje GKTG6SY2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info