Bedienungsanleitung Gorenje GW65 CLI (Seite 4 von 13) (Englisch)

603566

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Installing the foam

gasket

Before inserting the appliance into the opening in the kitchen worktop, the supplied

foam gasket must be attached to the lower side of the glass ceramic (glass) cooking

hob (see fi gure above).

Do not install the appliance without the foam gasket!

The gasket should be attached to the appliance in the following way:

- Remove the protective film from the gasket.

- Then, attach the gasket to the lower side of the glass, approximately 2-3

millimetres from the edge (as shown in the figure). The gasket must be attached

along the entire length of the glass edge and should not overlap at the corners.

- When installing the gasket, make sure that the glass does not come into contact

with any sharp objects.

Kitchen worktop cutoff

dimensions

• Only ovens fitted with a cooling fan may be installed underneath this cooking hob.

• Before installing an oven, the rear wall of the kitchen furniture element should be

removed in the area of the cooking hob cutout. Furthermore, a gap of at least 5 mm

should be left at the front side.

Installation procedure

(with springs)

• Worktop must be placed absolutely horizontal.

• Suitably protect the edges of the cut aperture.

• Connect the cooking hob to the mains power supply (see instructions for the

connection of the cooking hob to mains power supply).

• Put the supplied springs in their places.

• Insert the hob into the cut aperture.

• Press the hob firmly towards the worktop from above.

Installation procedure

(with fixing brackets)

The cook top is fixed to the unit by means of the brackets and accessories provided.

Holes are provided in the bottom of the tray where the self-threading plates (A) are

inserted so that you can attach the screws (C) that hold the brackets (B) in place.

A = plates for inserting on the bottom

of the cook top

B = fixing bracket

C = screw

CONNECTING

THE APPLIANCE

TO THE POWER MAINS

• The appliance may only be connected by an authorized skilled technician.

• Electric system protection should comply with all relevant regulations.

• The connection clips can be accessed when the connection clip covers are opened

/ removed.

• Before connecting the appliance, make sure the voltage indicated on the rating

plate is consistent with the voltage in your home circuit.

• The rating plate with basic information is attached on the lower side of the hob.

• The appliance is manufactured for use with the power supply voltage

220-240 V ~.

• In order to make a fixed connection to the mains, insert an all-pole circuit breaker

between the appliance and the mains. This device shall have a contact separation in

all poles, providing full disconnection under overvoltage category III conditions.

• Given the protection from the risk of fire, appliances of this type may be installed in

a worktop next to a piece of kitchen furniture that is taller than the appliance (when

installed); however, in this case, a kitchen furniture element must be installed on the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje GW65 CLI Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gorenje GW65 CLI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info