Bedienungsanleitung Gorenje k 7708 e (Seite 14 von 18) (Englisch)

326973

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

179732

Instructions for use, installation and connection

the cabinet of equal height as the appliance. Suspended

cabinets may be installed at such height as not to impede the

cooking process.

Minimum vertical distance from the appliance must be at

least 650 mm.

• In case the gas specifications do not correspond to the

requirements of the appliance, call the service center or

the gas supplier. Qualified technician will make

necessary amendments to agree with your type of gas.

• Any other amendments or replacements requiring tools, may

be performed by qualified personnel only.

• In any case, you are allowed to replace only such parts

which do not require any tools for their replacement!

• Panels, glue and furniture lining from artificial materials,

adjacent to the appliance must be temperature resistant

(>90°C), otherwise they might be deformed.

• Mains lead behind the cooker must be placed in such

manner to avoid touching the back panel of the cooker

because of the heat it develops during operation.

• Remove any packaging materials (foils, artificial foam, nails,

etc.) from the reach of children, because they represent

potential danger. Children may swallow small parts, or

suffocate with foils.

Leveling the appliance and extra support

(certain models only)

Your appliance is equipped with extra support. The height of

the cooker with the support is 90 cm, and without support it is

85 cm. Left and right side of the support is equipped with two

wheels to facilitate relocation. In the front part, on both sides

there are two adjustable screws, used to level the cooker and

adjust its upper edge in line with the adjacent kitchen furniture.

Adjustable legs are accessible when the drawer is pulled out.

Adjust the position of the cooker by turning the legs in one

direction or another. Adjustable legs will be turned easier if the

appliance is somewhat lifted up and tilted.

Additional support may be removed by unscrewing the four

screws holding it to the bottom of the cooker. In such case

relocate the adjustable screws from the support and place

them left and right at the bottom front base of the cooker. Level

the cooker as described earlier.

Some cookers are equipped with four adjusting screws (two in

front and two at the back), used for leveling the appliance or

adjusting its heights to match the adjacent furniture.

Manufacturer's adjustments

Gas cookers are tested and equipped with the symbol CE.

Gas cookers are supplied sealed and adjusted to natural gas H

or E (20 mbar) or to liquid gas (50 or 30 mbar). Specifications

are indicated on the rating plate, located in the interior of the

oven and accessible when the oven door is opened.

Gas load and consumption of particular burners are indicated

in the table below.

Modification to another type of gas requires the exchange of

gas nozzles. Information are indicated in the table below.

In case of damage or broken seal the functional components of

the cooker must be rechecked and resealed in accordance with

the instructions for installation.

Such functional components are: fixed nozzle for large flame

and adjustable nozzle for small flame.

Gas connections

• Connect the appliance in accordance with the regulations of

the local gas supplier.

• Gas cooker is equipped with the gas connection on the right

side with the exterior thread ISO 7-R1/2.

• Certain appliances are supplied with the attached liquid gas

coupling and the sealing gasket.

• The connection R1/2 must be gripped tight during the

connection procedure to prevent it from revolving.

• For sealing use only approved gaskets.

• The deformation of the non-metal gasket connection

thickness during tightening may not exceed 25%.

• Connect the appliance to the gas coupling by means of

certified flexible hose. The hose may not touch the bottom

panel of the appliance or the rear panel and ceiling of the

oven.

• Connect the appliance in accordance with the regulations of

the local gas supplier.

Important! Check all the connections for tightness after the

installation!

Flexible hose connection

In case the appliance is connected by means of a flexible

hose, the position A of the hose is not permissible.

In case the connection hose is made of metal, position A is

permissible.

Beginning of operation

Start using the appliance in accordance with the instructions

for use.

Lit up all burners and check the stability of the flame with high

and low setting. Adjust air intake if necessary.

After that, take time and explain the operation and control of

the appliance to the user and read with him the instructions for

use.

Liquefield gas connection

9 Pipe coupling liquefied

10 Gasket (certain models only)

11 Connection R1/2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje k 7708 e Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info