Bedienungsanleitung Gorenje RB4061 (Seite 5 von 44) (Alle Sprachen)

603425

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Mounting instructions for refrigerating and freezing appliances are for qualiﬁ ed technicians only.

Appliance should be mounted and installed in compliance with these instructions, current standards and

regulations. Mounting instructions were prepared for various types/models of appliances, therefore they

may describe some procedures that do not apply to your appliance.

Mounting Dimensions and Required Air Circulation

The rear wall of the appliance is getting warm during the operation of the appliance and water is evapo-

rating from the drain pan on the compressor. You must therefore provide for adequate air circulation on

the rear of the appliance.

At the base of the kitchen unit intended for building in the integrated appliance, there should be at least

200 cm² free space, for adequate air circulation.

On the upper part of the appliance the air is coming out, so try not to cover the opening for the outﬂ ow

air.

Changing the Direction of Opening the Door

If you ﬁ nd the direction of opening the door on your appliance inconvenient, you can change it. Holes on

the opposite side have already been prepared in the factory and are now plugged.

Remove the cover of the upper hinge, unscrew the hinge and take off the door (the door is not ﬁ xed on

the lower hinge).

Unscrew the upper rail, replace it to the opposite side of the appliance and ﬁ x it.

Remove the washer from the lower hinge and unscrew (rotate it in clockwise) the fastener on the lower

hinge.

Replace the fastener and the washer in reverse order into the opening of the lower hinge on the op-

posite side of the appliance.

Take off all door corners and interchange them (instead of the corner with a hole insert the one without

the hole and vice versa).

Put the door of the appliance on the lower hinge.

Fix the upper hinge and cover it.

Replace the slide guides to the opposite side of the door.

Plug the remaining holes with decorative caps.

Check the gasket, it shouldn’t be creased and it should seal well. In case it does not ﬁ t perfectly, pull it

out and rotate for 180°. In certain models it is not possible to replace the door gasket.Should the seal

not adhere to the casing of the appliance perfectly, it will have to be heated from a suitable distance (by

means of hair drier, for example) and lightly stretched to the required height.

Changing the Direction of Opening the Door on the Low Temperature Compartment

Unscrew the blocking element and the hinge of the low temperature compartment and take off the door.

Plug the holes with plastic caps provided.

Shift safety spring to the lower side of the door. (certain models only)

Turn the door for 180° and replace it on the opposite side of the low temperature compartment. Fix the hinge

and the blocking element of the door (position of holes already provided).

•

II.

Integrated Refrigerating and Freezing Appliances EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje RB4061 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gorenje RB4061

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info