Bedienungsanleitung Gorenje wa 614 syw (Seite 21 von 32) (Englisch)

313382

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

276657

Failure Possible cause Remedy

Greasy wads appear on

the laundry.

Too little detergent (laundry was

very greasy).

Wash the laundry again.

Add more detergent for such soiled

laundry, or use liquid detergent.

Laundry is stained after

washing.

You used liquid detergent or

detergent for colored laundry

which does not contain whitener.

Use the detergent containing

whitener.

White powdery residues

on the laundry.

It is not the consequence of bad

rinsing, but because of neo-

phosphate detergents containing

non soluble components

(zeolites) for water softening.

Such substances may be

deposited upon the laundry.

Immediately rinse the laundry once

again.

• Use liquid detergents which do

not contain zeolites.

• Try removing the residues with

the brush.

Detergent residues in the

dispenser.

Low water ﬂ ow pressure.

Some detergents may stick to the

dispenser rather hard if it is wet.

• Clean the inlet pipe ﬁ lter net.

• In case of low water pressure

increase water level.

• Wipe the dispenser prior loading

detergent.

Softener is not completely

rinsed, or water is left in

the dispenser dish.

Sucking cover is not correctly

positioned or is clogged.

Clean the dispenser and ﬁ rmly ﬁ x

the cover to its place.

Unpleasant smell in the

washing machine drum.

• Remains of fabrics, washing

agent and softener in the ﬁ lter.

• Development of germs

• Check whether the ﬁ lter is clean.

• Run the auto-clean (SterilTub)

program (see chapter: selecting

additional functions)

Washing time is longer

than usual.

Time indicated on the

display is corrected during

the washing cycle.

• Low temperature of inlet water.

• Due to unevenly distributed

load, the machine has activated

the UKS*.

• Low mains voltage.

• There has been a failure in the

power supply.

• Washing program time may be up

to 60% longer; however, this does

not imply a fault in the machine.

• Washing time is extended by the

power supply down-time.

FAILURE 1

Program temperature not

reached (the machine

reports a failure - the

LEDs periodically ﬂ ash

once)

Temperature sensor disconnected

from the electronic circuit.

• Turn off the appliance and wait for

a few seconds;

• turn the appliance back on and

repeat the washing program.

If the failure is reported again, call a

service technician.

FAILURE 4

Spinning rpm not reached

in the selected program

(the machine reports

a failure - the LEDs

periodically ﬂ ash four

times)

(in some models,

FAILURE 2 is displayed)

• rpm sensor disconnected

• Motor overload due to too high

water level (manual addition of

water) or too big laundry load

• Motor failure

• Turn off the appliance and wait for

a few seconds;

• turn the appliance back on and

repeat the washing program.

If the failure is reported again, call a

service technician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje wa 614 syw Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info