512903
22
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
141373
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
Dimensions (w x d x h): 600 mm x 600 mm x 850 mm
Dimensions (w x d x h): 600 mm x 440 mm x 850 mm
Depth with door open: 106 cm / 88 cm (depending on model)
Weight (net): 90 kg / 79 kg (depending on model)
Nominal voltage: 230 V, 50 Hz
Power: 2300 W / 2000 W (depending on model)
Max. load: 7 kg / 6 kg / 4,5 kg (depending on model)
Power socket: (230 V, 50 Hz, 10 A)
Water pressure: min. 0,05 MPa, max. 0,8 MPa
Fuse: 10 A
3
Description of washing machine
Technical information
(depending on model)
141373
Open the door of the machine.
Load the laundry into the drum.
Close the door.
Open the water inlet faucet.
Push the ON/OFF button and select the program.
Add washing and treatment agents (detergent and softener).
Start the operation by pushing the START knob (F).
- Open the door of the machine.
Door is opened by pulling the handle (lever) on the right hand
side of the door towards you.
- Sort the laundry by the type of fabrics.
Do the buttons and zippers, tie the strings and pull out
the pockets.
Very delicate laundry should be put in a special
protective sack.
It is suggested to load the drum with items of different
sizes.
Pay attention to the labels on the clothes, indicating
the recommending washing mode (see table of
textile treatment symbols on the last page of these
instructions).
- Load the laundry into the drum.
Check that the drum is empty.
- Close the door of the appliance.
- Open the water inlet faucet.
- Push the ON/OFF button and select washing program.
Program is selected by turning the program selector (A) from the
“0” position to the desired washing program. The ON/OFF signal
LED indicating particular washing stage for the chosen program
starts ashing. The program selector (A) may be turned in both
directions, and the appropriate program selected according to the
type of laundry washed and the required washing temperature
(see Program Chart for help). You may select basic or partial
programs.
Select additional functions by pressing their relevant knobs (F).
- Selection of basic programs (
, , , , , )
Basic programs represent integral programs containing all
washing stages, including softening and spinning (see Program
Chart). They are selected by turning the program selector (A) to
the appropriate position.
Cotton: whites/colored
Normally stained cotton and ax bed linen and underwear, table
Washing procedureWashing procedure
Washing machine
operation
Washing machine
operation
9
141373
cloth, bathroom towels, top garments, etc.
For heavily stained permanent press use the heavy duty
program,
or program with the pre-wash .
If you wish the laundry not to be excessively creased at the end
of washing, use easy ironing program
.
Synthetics
Normally stained shirts, blouses and other polyester and
polyamide garments, or a mixture of these fabrics with cotton.
For heavily stained permanent press use program with pre-wash
.
Delicate
This is a program for delicate fabrics (dresses, skirts, blouses)
and curtains.
Wool
Especially gentle program for washing wool and garments made
from mixture of other fabrics with wool, appropriately marked for
machine washing.
Manual wash
Very gentle program concluded with short gentle spin (max. 400
RPM).
It is suitable for washing fabrics from ax, silk, wool or viscose,
marked accordingly for manual wash.
Mix
Special program for washing normally stained colored laundry made
from various resistant fabrics at 30°C.
- Selection of additional function ( , , , , , )
Additional functions alter the basic washing cycle procedure.
Particular function is switched on by pressing the relevant knob.
The selection is con rmed with sound signal and switching on
the signal LED above the selected function. If certain function
is not available for the selected program, signal LED will not
illuminate.
The function is switched off by pressing the same button again
- signal LED goes off.
Select the particular function after the selection of the
basic program, but prior pressing the START button
(F).
Pump stop
This function is switched on after the selection of a basic
program by pressing the knob (E). It may also be switched on
10
141373
during the operation, prior last rinse. Indicator LED above the
washing cycle symbol is lit.
The program stops at the end of last rinse, prior spinning:
laundry remains soaked in water and prevents crease, if you
are unable to remove it from the drum immediately after the end
of washing cycle.
Indicator LED above the knob is ashing.
The selected program is completed by pushing the START
button (F), but you may also apply partial programs (pumping
or spinning), but you must rst return the program selector (A)
to the “0” position for at least one second, prior selecting any of
the partial programs.
When program continues, indicator LED above the knob goes
off.
Higher water level (Water plus)
For better rinse, which is important for extra sensitive skin to
detergents.
For washing heavily stained laundry.
Half-program
Used for washing smaller quantities of laundry.
Reduced consumption of detergents and water, and shortens
washing time.
Short program
Convenient for washing less stained laundry.
Washing time is reduced (see Program chart).
Reduced spin RPM
Reduction of spin RPM depends on program selection and
maximum RPM for particular type of machine.
Basic programs Spin speed - RPM
max. reduced
Cotton 1400/1300
1200/1100
1000/900/800
700
600
500
Synthetics , Mix 1000/900/800 600
Delicate 700 0
Wool 600 0
Manual wash 400 0
Spin OFF (RPM - 700 RPM).
This knob switches off spin on all programs.
11
141373
PAUSE knob
By pressing the PAUSE knob (F) program may be suspended
at any time. After certain time you may open the door if there is
no water in the drum, otherwise this is not possible. Program is
continued by pressing the START knob (F).
• Failures
Program is suspended in case a failure occurs. Signal LED’s
are ashing and sound signal is heard (see cf. Failures).
Power failure
At electric cutout the program is interrupted, however, after the
power supply has been re-established, the program operation
automatically proceeds.
If a power failure occurs when the drum is still full of
water, be careful not to open the door before you pump
the water out.
• Child lock
- It is switched on by simultaneously pressing the elevated
water level knob
(D) and half-load /short program
knob
(C) for at least 3 seconds. Selection is con rmed by
the sound signal and illuminated signal LED. The function is
switched off following the same procedure.
- As long as the Child lock function is engaged you may not
alter the program or additional functions. You may merely
switch off the machine by turning the program selector (A)
to the position “0”. Child lock remains active even after the
appliance is switched off, and you have to disengage it if
you want to select a new washing program.
Setting the sound signal
The appliance has the possibility of setting stronger sound
signal. Press the Reduced spin RPM knob
(or Spin off knob
) and switch the machine on. The selection of the function
is con rmed by the sound signal. The function is disengaged
following the same procedure.
Special functionsSpecial functions
14
141373
Disconnect the washing machine from the mains
before cleaning!
The casing should be cleaned with soft cloth and mild
detergent.
The interior of the drum and the door gasket is cleaned by
washing at 60°C without laundry and adding half quantity of
detergent.
If necessary, clean the detergent dispenser. Pull it out from its
casing completely by pressing the ap (see Fig.).
If necessary, clean the cover of the bung under the running
water.
Insert particularly delicate linen (stockings, delicate female
underwear, etc.) into the special bag.
High spin RPM leave less moisture in laundry which dries out
much quicker in the tumble dryer, thereby saving energy.
Do not put clods of detergent into the soap dispenser
as the tube in the washing machine may clog.
16
Cleaning and maintenance
141373
Wash it under running water using a brush, and dry it. Remove
any leftover dried detergent from the bottom of the casing.
Clean the entire rinsing area of the washing machine with a
brush, especially the nozzles on the upper side of the rinsing
chamber.
Clean frequently the water inlet hose screen under running
water.
After each wash wipe the door rubber gasket. This will prolong
its useful life.
• Open the lter lid using at screwdriver or similar tool.
Filter needs occasional cleaning, especially following heavily
shaggy or old laundry. Before cleaning, drain any water from
the machine via drain pipe.
Turn it anti-clockwise, pull it out and clean under running
water.
17
141373
• Insert the lter back as shown on the picture (arrow and
pointer), and tighten by turning it in clockwise direction. To
ensure good sealing the gasket surface (A) must be dirt free.
The washing machine automatically monitors the execution of particular functions during the
operation, and reports any detected failures. In such cases both signal LED’s start ashing in
certain sequence, accompanied by the audible signal, sounding in the same sequence as the
indicator LED’s ash. The ashing sequence changes in accordance with the nature of the
detected failure.
In some cases you may attempt removing certain failures yourself, so count the number of ashes,
repeating after certain pauses.
The machine signals failures immediately after detecting them and stops the program, except for
heater failure, where the machine completes the washing program without heating water.
Failures
In certain cases you may remove the failure yourself:
2 - two ashes: door is not correctly closed
3 - three ashes: inappropriate water intake
7 - seven ashes: inappropriate water outlet.
In all other instances mark the number of ashes indicating the failure, switch off the machine and
call nearest authorized service center (LED’s continue ashing until you switch the machine off).
Interferences from the ambient (for example electrical wiring) could induce signalization of different
faults. In such cases:
- switch the appliance off, and wait for a few seconds;
- switch the appliance back on and repeat the washing program.
If the fault repeats, call authorized service shop.
Warranty shall not apply in case of failures due to interferences from the environment (lightning
stroke, power supply circuit faults, natural disasters).
18
Failures
141373
19
Failure Possible cause Remedy
The machine does not
work (indicator LED’s
are not illuminated).
Machine is not powered. Check if:
power in the socket,
the fuse is OK,
plug is in the socket.
Washing program
does not start
(washing stage LED is
ashing).
Door is not properly closed. Push it towards the machine.
Water does not enter
the machine (after
approx. 8 min the
machine reports
failure -3 ashes).
Disturbed water inlet. Check if:
the water faucet is open,
inlet pipe net lter is clean.
Push the START button.
Water is leaking from
the machine.
Filter is not tightly screwed in.
Inlet pipe is not tightly screwed
to the machine or to the water
faucet.
Outlet pipe fell to the oor.
Tighten the lter properly.
Tighten the inlet pipe.
Af x the outlet pipe to the drain.
The machine moves
during operation.
The machine is not properly
leveled.
Transport brackets are not
removed.
Level the machine with the adjustable
legs.
Remove transport brackets.
The machine vibrates
during the spin.
Unevenly distributed laundry,
especially with very small
quantities (for ex. only the
bathrobe).
This is normal, the machine will
reduce the RPM if vibrations are too
strong.
Wash larger quantity of laundry.
Excessive foaming
during washing.
Excessive measure of detergent. Use washing powder according to
the instructions by the producer and
according to the water hardness and
soiled laundry.
Use only detergents for machine
washing.
Water is poorly
pumped out or not at
all (machine reports
failure - seven ashes
of LED).
Water outlet is clogged. Check if:
• the lter is clean,
outlet pipe is not jammed,
outlet pipe is positioned higher than
1 m.
Push START again.
Laundry is not
properly spun.
No failure is reported.
The machine switched on the
UKS* function. Because of bad
laundry balance, the machine
has automatically reduced spin
RPM.
The machine operates normally.
Wash large and small pieces of
laundry together.
Greasy wads appear
on the laundry.
Too little detergent (laundry was
very greasy).
Wash the laundry again.
Add more detergent for such soiled
laundry, or use liquid detergent.
141373
* Testing program by EN 60456 with the selection of max. spin
RPM.
** Depending on model.
21
Basic programs
Max. load
Temp. (°C)
Spin (max. RPM)
Duration (min.)
Water cons.
L
Energy cons.
kWh
RPM RPM
400 - 700
800 - 900
1000 - 1400
400 - 1400
Cotton 7 95
1400
156 67 62 55 2,31/2,19**
Cotton 7 60 126 61 56 49 1,31/1,17**
Cotton + prewash 7 60 157 71 66 59 1,45/1,32**
Cotton - heavy * 7 60 147 61 56 49 1,33/1,19**
Cotton 7 40 128 61 56 49 0,67
Cotton - easy ironing 3,5 60
1000
122 61 56 49 1,14
Synthetics 3,5 60 111 46 46 46 0,97
Synthetics 3,5 40 100 43 43 43 0,56
Delicate 3 40
700
59 58 58 58 0,48
Delicate 3 30 53 58 58 58 0,39
Wool 2 40
600
51 42 42 42 0,32
Wool 2 30 46 42 42 42 0,20
Manual wash 1,5 30 400 47 50 50 50 0,25
Mix 3,5 30 1000 72 43 43 43 0,35
Partial programs
Rinse
3,5 700 25 40 0,02
Softening
7 1000 15 18 0,02
Pumping water
7-2
Spinning
7 1400 12 0,03
Tables
Program chart
- 7 kg
141373
* Testing program by EN 60456 with the selection of max. spin
RPM.
** Depending on model.
22
Basic programs
Max. load
Temp. (°C)
Spin (max. RPM)
Duration (min.)
Water cons.
L
Energy cons.
kWh
RPM RPM
400 - 700
800 - 900
1000 - 1400
400 - 700
800 - 1400
Cotton 6 95
1400
139 63 58 51 2,30/2,10** 2,10/2,05**
Cotton 6 60 119 57 52 45 1,28/1,12** 1,12/1,00**
Cotton + prewash 6 60 150 65 60 53 1,50/1,34** 1,34/1,22**
Cotton - heavy * 6 60 140/150** 57 52 45 1,30/1,14** 1,14/1,02**
Cotton 6 40 121 57 52 45 0,70/0,66** 0,66
Cotton - easy ironing 3 60
1000
115 57 52 45 1,10 1,10
Synthetics 3 60 106 43 43 43 0,93 0,93
Synthetics 3 40 95 40 40 40 0,52 0,52
Delicate 2,5 40
700
59 55 55 55 0,45 0,45
Delicate 2,5 30 53 55 55 55 0,36 0,36
Wool 2 40
600
51 42 42 42 0,32 0,32
Wool 2 30 46 42 42 42 0,20 0,20
Manual wash 1,5 30 400 47 50 50 50 0,25 0,25
Mix 3 30 1000 72 40 40 40 0,32 0,32
Partial programs
Rinse
3 700 25 40 0,02
Softening
6 1000 15 16 0,02
Pumping water
6-2
Spinning
6 1400 12 0,03
Program chart
- 6 kg
141373
25
Normal wash
Delicate wash
Max.
washing
temp. 95°C
Max.
washing
temp.
60°C
Max.
washing
temp.
40°C
Max.
washing
temp.
30°C
Manual
washing
Washing
not
allowed
Whitening
Whitening in cold water
Whitening not allowed
Ironing Hot iron max.
200°C
Hot iron max.
150°C
Hot iron max.
110°C
Ironing not
allowed
Dry cleaning Dry cleaning in all
solvents
Perchlorin-
etyhlene
R11, R113,
Kerosene
Dry cleaning in
kerosene, in pure
alcohol and in
R 113
Dry cleaning not
allowed
Drying Place on
at surface
Hang wet Hang
High
temperature
Low
temperature
Tumble drying
not allowed
Maintenance chart
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gorenje WU62101 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info