590606
15
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
GMC-I Messtechnik GmbH 15
Adjusting Cable Resistance
Ð After selecting a resistance thermometer, the
measurement display is accessed by pressing the key.
Ð The menu for cable resistance adjustment is opened by
simultaneously pressing the and keys. Rlead and
temp are displayed.
Ð The decade (i.e. the position of the digit to be changed) is
selected with the  keys, and the respective digit is
set with the  keys.
Ð The menu is exited upon acknowledging the last digit by
pressing the key, whereupon the measuring display
returns. The cable resistance value remains in memory.
The default value is 0.1 Ω. Entry is limited to a range of 0
to 50 Ω.
Note!
The selected cable resistance value remains
unchanged after exiting the function, and when the
instrument is switched off.
11 Insulation Resistance Measurement [MΩ@...V]
(METRA HIT 27I only)
11.1 Preparing for Measurement
Note!
High-resistance measurements
In the event of extremely high resistances the
capacitive influence of the person performing the
measurement and/or the measuring cable may
distort the measured value. Use therefore short or
shielded measurement cables.
The measurement cables may not come into contact
with one another during high-resistance insulation
measurements.
Ð Set the rotary selector switch to “MΩ@50V”, “100V”,
“250V” or “500V”, depending upon the desired test
voltage.
Ð Connect the DUT as shown on the next page.
Note!
Interference voltage
The rotary selector switch may only be set to
MΩ@...V for insulation resistance measurement
(not for voltage measurement).
However, if interference voltage is inadvertently
applied with the switch in this position, it is displayed
at the bottom left. Insulation resistances may only be
measured on voltage-free objects.
If an interference voltage of > 50 V is present, insulation
resistance measurement is disabled. The LCD continues to
display the interference voltage value. If a voltage of greater
than 610 V is present, an acoustic signal is generated as well.
mΩ
S+S–
VΩ°C
RTD
see chapter 14
Measuring Range:
- - - - -
V
-000 250 V
MΩ@
50 ... 500V
10.29
V
023 250 V
MΩ
Selected Test Voltage
Displays test voltage
as long as key is depressed
R
ISO
FUNC MAN
+
FUNC
Continuous
Measurement
Measuring voltage
/Residual voltage
approx. 2% accuracy
Nominal/
test voltage
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

gossen-metrawatt-metra-hit-27i

Suche zurücksetzen

  • Gibt es für das Gossen Metrawatt M205A einen Schaltplan? Eingereicht am 13-12-2019 10:46

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt METRA HIT 27I wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Gossen Metrawatt METRA HIT 27I

Gossen Metrawatt METRA HIT 27I Kurzanleitung - Deutsch, Englisch - 4 seiten

Gossen Metrawatt METRA HIT 27I Bedienungsanleitung - Holländisch - 28 seiten

Gossen Metrawatt METRA HIT 27I Kurzanleitung - Französisch - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info