Bedienungsanleitung Gossen Metrawatt METRA HIT H-E CAR (Seite 18 von 28) (Englisch)

590612

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

18 GMC-I Messtechnik GmbH

12.2.2 Memory Mode Operation – STORE Menu Function

Ð First set the sampling rate for memory mode operation,

and then start memory mode operation.

The sampling rate can also be changed during memory

mode operation.

Ð First select the desired measuring function and an

appropriate measuring range.

Ð Check the storage battery charge level before starting

long-term measurement recordings, see chapter 14.1 on

page 25. Connect the charger if necessary.

Starting Memory Mode Operation with Menu Functions

Ð Open the “Operating Mode” menu (refer to the menu

diagram) and select the StorE function.

Ð Now activate the  key to open the start menu for

memory mode operation: StArt blinks.

Activate the key once again in order to start memory

mode operation: REM appears at the display.

Ð Press the  key in order to switch to the measuring

function.

A new memory block is created when another measuring

function is selected with the rotary switch or the FUNC key.

Data storage then continues automatically. The “SLEEP

MODE” is still active, i.e. the device is switched on and off

automatically at sampling rates of long duration

(see chapter 2).

When memory capacity has been exhausted, MEMO FULL

appears at the display, and an acoustic signal is generated

simultaneously. The signal can be deactivated by pressing

any key.

REM Display

The REM symbol indicates that memory mode operation has

been activated via menu function STORE.

Press the  key if you wish to monitor the measured values

also during the memory process.

The „STORE“ function cannot be started while the „DATA“

function is activated.

Exiting Memory Mode Operation with Menu Functions

Ð Select the StorE menu.

Ð Activate the  key: StOP blinks.

Ð Activate the  key once again: the auxiliary displays are

cleared. Memory mode operation has now been

deactivated.

Ð Press the  key in order to return to the measuring

function.

Ð Memory mode operation can also be exited by switching

the instrument off.

12.3 Querying Memory Occupancy – INFO MEMO/OCCUP

Memory occupancy can be queried from the „1NF0 “ menu.

The main display shows current occupancy as a percentage

between 001 and 100%

12.4 Clearing the Memory – MEMO CLEAr

Attention!

This function deletes all measured values from

memory.

This function cannot be performed during memory mode;

bUSY

MEMO

is displayed instead of CLEAR.

12.5 Activating the Default Values

Previously entered changes can be undone, and the default

settings can be reactivated. This may be advisable after the

occurrence of software or hardware errors.

Ð Simultaneously press and hold the FUNC, MAN|AUTO and

DATA|CLEAR keys, and switch the instrument on with the

ON|OFFkey.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRA HIT H-E CAR Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Metrawatt METRA HIT H-E CAR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info